Electriq EPMH1000LED 1 KW slim wall mountable panel heater
Our goal is to provide you with high-quality appliances and electronics at a far lower cost than the major brands. To achieve this, we source from the same manufacturers as the major brands, maintaining quality without sacrificing any additional costs for the big brand name. We can help you save money on any new kitchen item, TV, security system, or monitor that you may need.
- Carefully read the instructions before operating the unit
- This appliance is for indoor use only.
- Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
- Installation must be by the regulations of the country where the unit is used.
- If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
- This heater has been tested and is safe to use. However, as with any electrical appliance – use it with care.
- Disconnect the power from the unit before dismantling, assembling, or cleaning.
- Avoid touching any moving parts within the appliance.
- Never insert fingers, pencils, or any other objects through the guard.
- This appliance can be used by Children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be carried out by children.
- Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance safely and understand the hazard since lived. Children aged from 3 years and less than 8 years shall not plug in, regulate, or clean the appliance or perform user maintenance.
- Children under 3 years should be kept away unless continuously supervised.
- Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
- Do not clean the unit by spraying it or immersing it in water.
- Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
- Never operate this appliance if the unit, cord, or plug is damaged. Ensure the power cord is not stretched, exposed to sharp objects/edges, or routed under the unit.
- Any service other than regular cleaning should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
- Never use the plug as a switch to start and turn off the heater. Use the provided power switch on the rear of the unit.
- Do not use an external timer.
- Do not cover the air inlet or outlet, or place items close to the unit which may restrict airflow, as this may present a fire risk.
- The heater must not be located immediately below a socket outlet.
- Always ensure the unit is secure before operation. Do not use on unstable or uneven surfaces and if wall-mounted, it must be securely attached to a suitable wall.
- Do not move or tilt the unit.
- Avoid keeping the unit in direct sunlight for a long period.
- The heater is designed to be used at temperatures above -20°C. If it is exposed to temperatures below this, it must be allowed to warm above this level before operation.
- Do not attempt to repair, disassemble, or modify the appliance. This unit contains no user-serviceable parts.
- Always unplug or disconnect the appliance from the mains power supply when not in use, or when moving or cleaning it. Do not pull the cord to unplug the heater.
- Keep the heater clean. Do not allow any object to enter the ventilation or exhaust opening as this may cause electric shock, fire, or damage to the heater.
- Do not use the appliance for anything other than its intended use. It is designed for domestic indoor use only.
- There may be a trace of odor during the first few minutes of initial use or after a period of storage. This is normal and will quickly disappear.
- This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or any flammable liquids are used or stored.
- Never locate this appliance where it may fall into a bathtub or otherwise be exposed to water.
- This appliance is IP24 rated, and so can be used or installed within a bathroom as long as the appliance and its cables are not within Zones 0-2.
- If used within a bathroom, the circuit must be protected by a suitable RCD to prevent electric shock.
- Do not allow the appliance to be submerged or sprayed with water.
- If the unit is wall-mounted, it must be installed according to current regulations for the area of installation. If unsure, professional advice should be sought.
- The remote contains a lithium battery, which keeps it out of reach of small children. Seek medical advice if swallowed.
- To prevent battery leakage: Remove the battery from the remote if exhausted or before long periods of storage.
- WARNING: To reduce the risk of fire or electrical shock, DO NOT use this appliance with any solid-state Speed Control Device or any variable speed controllers.
ENERGY SAVING AND UNIT SAFETY PROTECTION TIP
- Do not cover or restrict the airflow. Do not use it in a dusty environment.
- For safety and maximum performance, when used as a portable unit the minimum distance from a wall or objects should be 50cm.
The heater can be fitted with the supplied legs to use as a portable unit or wall-mounted. Do not use the unit without the legs unless it has been wall-mounted.
FITTING THE LEGS
Unscrew the two screws holding the wall mounting bracket to the back of the body, and keep in a safe place to allow the option of wall mounting in the future.
Attach the legs by securing them to the base of the heater using the screws provided. Once the legs are attached, slot the supplied castors into the holes until they fully engage.
Before drilling any holes, it is the responsibility of the installer to ensure that there are no pipes or cables that may be damaged during installation. The unit should not be plugged in until installation is complete.
Unscrew the two screws holding the wall mounting bracket to the back of the body.
Place the wall bracket in position on the wall, using a spirit level to ensure it is straight. Mark the position of the mounting holes using a Pencil. Drill the holes at the marked position using a suitable drill bit.
Insert the wall plugs into the holes before fixing the bracket to the wall using the supplied screws. Ensure that the bracket is secure.
Fit the heater into the wall bracket, ensuring it is correctly positioned and the screw holes line up.
Tighten the two screws on the top of the bracket, ensuring the unit is secure, before connecting the power.
When the room temperature reaches the desired level, the heater will change to Low Heat mode. When the room temperature is 2 degrees over the desired temperature, the heater will enter standby mode. The heater will resume operation when the temperature drops 2 degrees below the desired temperature.
CLEANING AND STORAGE
ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance.
CLEANING THE SURFACE
- Clean the heater with a duster or a soft wet cloth. Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or gaps in the casing.
- Do not run the unit until completely dry.
- Place the heater in its original box or cover to protect it from dust when not inuse.
- Store it in a cool dry place.
Do not repair or disassemble the unit by yourself, unauthorized repair attempts will invalidate the warranty and may cause bodily harm.
electric UK SUPPORT
Please, for your convenience, make these simple checks before calling the service line. If the unit still fails to operate call: 0871 620 1057 or complete the online form.
- Is the unit plugged into the mains?
- Is the fuse OK?
- Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
Office hours: 9 AM – 5 PM Monday to Friday
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA
Disposal: Do not dispose of this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.
FAQs About Electriq EPMH1000LED 1 KW slim wall mountable panel heater
Are panel heaters put on walls a suitable option?
Panel heaters are a great option since they operate on autopilot, heat up quickly, and adjust their output to balance the storage heaters’ residual heat. They will also use less higher-rate daytime electricity because they are more efficient than other portable top-up heaters like fan heaters.
What is the electricity consumption of wall panel heaters?
Mill Panel Heaters come in eight different wattage ranges, from 250W to 2000W, for either glass or steel. It is crucial that the heater’s overall wattage impact is sufficient for the size of the space it will be heating, regardless of the model you select.
Do wall panel heaters have low operating costs?
Although initially less expensive, electric panel heaters eventually cost more to operate. This is so that they may continuously draw power from the power source to heat the air, as electric panel heaters do not store heat. Electric radiators, on the other hand, only need electricity when they are heating the storage medium.
Are heaters with wall panels safe?
There are no gas, flame, or chemical safety hazards associated with electric wall heaters. They do, however, feature heated coils that have a high heat capacity. Steer clear of these and the device itself. In light of this, an electric device is hardwired and does not require power strips or extension cords.
Are panel heaters energy-efficient devices?
Convective heat is intrinsically less efficient than radiated heat, which is why panel heaters are less efficient than electric radiators. This implies that using panel heaters to heat your space will use more power than using energy-efficient electric radiators.
Are wall heaters energy-hungry devices?
The average operating cost of an Envi wall-mounted heater is four to five cents per hour. In contrast, alternative types of central heating systems (gas and electric) can cost as much as 18 cents per hour for fan and radiator heaters. Most central heating systems use more energy from their attic blower fan than from a single 400-watt panel heater.
What drawbacks do wall heaters have?
Achieving the Correct Temperature in Different Rooms Takes Longer. Once more, wall heaters require more time to reach the ideal temperature in various rooms as they do not require ductwork. If you need to swiftly heat several rooms at your house or place of work, this could be an issue.
Is the air dried by panel heaters?
Since panel heaters don’t require fans, the space can retain some of its humidity and the air doesn’t dry up.
Is it possible to use a wall panel heater overnight?
We may state that it’s advisable to turn off electric heaters before going to bed and to avoid leaving them on all night.
Panel heaters: Are they noisy?
Panel heaters are ideal for bedrooms, workplaces, and other quiet areas because of their silent operation. Panel heaters operate quietly, making it possible for you to work or sleep without being bothered, in contrast to traditional heaters that can be noisy and irritating.
For more manuals by Electriq ManualsDock