Minn Kota 1866350 Legacy i-Pilot System Remote Manual

Minn Kota 1866350 Legacy i-Pilot System Remote

About Minn Kota

When you combine your Humminbird with Minn Kota engines and shallow water anchors, the combination becomes even more formidable. It transforms your boat into an autonomous fishing device. allows you to automatically track contours of depth. This allows you to operate any aspect of your boat from any location on it.

In Mankato, Minnesota, genuine American fishermen develop, build, and maintain every Minn Kota motor. We’ve been keeping an ear to the ground to improve everything you love about fishing for almost nine decades.

Manuals Control

• Steer Left
• Steer Right
• Prop On/Off
• Speed Down
• Speed Up
• High-Speed Bypass Toggles the motor speed between its current setting and speed
• Backlight Turns the remote LCD backlighting on for six seconds.
• Keypad Lock/Unlock To lock or unlock the keypad press and hold the backlight button for 3 seconds.

CRUISE CONTROL/ AUTOPILOT

• Advanced AutoPilot and AutoPilot Turns Advanced AutoPilot on and off when pressed once. Turns AutoPilot on when held for two seconds.
• Cruise Control Turns cruise control on and off using the current GPS speed as the target speed.

TRACKS

• Track to End Navigates to the nearest location on a previously recorded track and follows it to its end.
• Track to Start Navigates to the nearest location on a previously recorded track and follows it to its start.
• Track Record Starts and ends the recording of a track to a selected memory location.
• Record Pause/Escape Pauses the recording of a track and then resumes the recording when pressed again.

SPOT LOCK

• Spot-Lock Turns spot lock on and records it to a memory location.
• Spot-Lock Recall Recalls a spot-lock location from memory and turns spot-lock on.

ENGAGING SPOT LOCK

1. Press the Spot-Lock button on the remote.
2. The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down Pressing the Spot-Lock button again or waiting for three seconds accepts the memory location.

DISENGAGING SPOT LOCK

To disengage Spot-Lock press any of these buttons: Prop On/Off, Steer Right, Steer Left, Speed Up, Speed Down, or Spot-Lock.

RE-ENGAGE A SAVED SPOT LOCK LOCATION

1. Manually navigate the boat to within a quarter mile of the saved Spot-Lock location. Due to safety reasons, i-Pilot will not re-engage a saved Spot-Lock location greater than a quarter mile away.
2. Press the Spot-Lock Recall button on the remote.
3. The Memory Location icon will flash on the remote LCD for three seconds allowing you to choose a memory location by pressing the Speed Up or Speed Down buttons. Pressing the Spot-Lock Recall button again or waiting for three seconds accepts the memory location.

SPOT LOCK ESCAPE

If the Spot-Lock button is accidentally hit, press the Record Pause/Escape button or any manual navigation button within three seconds to cancel the command.

ENGAGING CRUISE CONTROL

1. Press the Cruise Control button on the remote.
2. The current GPS speed will flash, displaying your current speed as the target GPS speed on the remote LCD for three seconds.
3. Press the Speed Up or Speed Down buttons to increase or decrease the target speed or press the Cruise Control button again to engage the Cruise  Control

DISENGAGE CRUISE CONTROL

Pressing the Cruise Control button will disengage Cruise Control.

ADjUSTING TARGET SPEED WITh  CRUISE CONTROL ENGAGED

With Cruise Control engaged press the Speed Up or Speed Down buttons to adjust the target speed by 0.1 MPH increments.

ENGAGING ADVANCED  AUTOPILOT AND AUTOPILOT

1. To engage Advanced AutoPilot, press the AutoPilot button once. To engage AutoPilot, press and hold the AutoPilot button for two seconds.
2. The Advanced AutoPilot or AutoPilot icon will be displayed on the remote LCD.
3. To adjust the desired heading, manually steer the motor to a new heading. i-Pilot will lock onto a new heading.

RECORDING A TRACK

1. Press the Record button on the remote.
2. The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down  Pressing the Record button again or waiting for three seconds accepts the memory location.
3. The REC icon will be displayed on the remote LCD. Remember this will be the starting point on the track. Navigate the boat along the desired path or course.  AutoPilot and/or Cruise Control can be used while recording a track.
4. Press the Record button on the remote again to stop the recording. The recording will end automatically if the two-mile distance limit is reached for the track or if one of the following buttons is pressed: Spot-Lock, Spot-Lock Recall, Track to End, or Track to Start.

PAUSE AND RESUME A RECORDING

1. While recording a track press the Record Pause/Escape
2. The record icon will flash on the remote LCD.
3. i-Pilot has now paused the recording of the track.
4. If the boat moves farther than a quarter mile from where the Record Pause/Escape button was pressed, the recorded track will be ended and saved to the memory location previously selected.
5. When ready to resume recording, navigate the boat just ahead of where the Record Pause/Escape button was pushed.  Failure to do this may cause erratic playback of a track.
6. Push the Record Pause/Escape
7. The record icon will stop flashing on the remote LCD.
8. i-Pilot is now recording again and adding to the track that was paused.

REPLAYING A TRACK  (TRACK TO START / TRACK TO END)

1. Manually navigate the boat to within a quarter mile of the saved track. Due to safety reasons, i-Pilot will not re-engage a saved track greater than a quarter mile away.
2. Press the Track to Start or Track to End button on the remote.
3. The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down  Pressing the button pressed in step 2 again or waiting for three seconds accepts the memory location.
4. Adjust motor speed to the desired setting to engage and navigate the track automatically.

RECORD, TRACK TO END, AND TRACK  TO START ESCAPE

If the Record, Track to Start, or Track to End button is accidentally hit, press the Record Pause/Escape button within three seconds on the remote to cancel the command.

FAQS About Minn Kota 1866350 Legacy i-Pilot System Remote

What is the Minn Kota 1866350 Legacy i-Pilot System Remote?

For more manuals by Minn Kota Manuals Dock