Welcome to ManualsDock! Read Millions of manuals for free.

LG HF65LA Full HD Home Theater Owner Manual

LG HF65LA Full HD Home Theater FEATURE

LG LOGO

LG HF65LA Full HD Home Theater

LG HF65LA Full HD Home Theater PRODUCT

ABOUT LG Electronics

Globally, LG Electronics concentrated on creating breakthroughs. We are dedicated to offering customers electronic products that improve their quality of life. To enable this, we want to keep enhancing consumers’ lives. We provide a comprehensive selection of goods in several categories, such as TV and home Entertainment, Kitchen, Laundry, Computers, Air Conditioning, and solar. Learn more about LG right now. For additional information, speak with the LG salesperson in your area.

SAFETY PRECAUTIONS

Please take note of the safety instructions to prevent any potential accident or misuse of the projector.

Child injuries can be prevented by following these simple safety precautions. The precautions should be followed in the same manner when you store or move your existing projector.

  • Safety precautions are given in two forms, i.e., WARNING and CAUTION as detailed below.

 WARNING  Failure to follow the instructions may cause serious injury and even death.

 CAUTION  Failure to follow the instructions may cause personal injury or product damage.

  • Read the owner’s manual carefully and keep it on hand.

Indoor Installation

WARNING

  • Do not use the projector outside and do not expose the product to any humidity or water.

– Since the product is not waterproof, this may result in a fire or electric shock.

  • Do not place the projector in direct sunlight or near heat sources such as radiators, fires, stoves, etc.

– This may result in fire.

  • Do not place flammable materials such as aerosols near the projector. – This may result in fire.
  • Do not allow children to cling to or climb up to the projector.

– This may cause the projector to fall, causing injury or death.

  • Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a closet) or on a carpet or cushion.

– This may result in fire due to the increase in internal temperature.

  • Do not place the product close to sources of steam, oil, or oil mist, such as humidifiers and kitchen counters.

– Failure to do so may result in fire, electric shock, or corrosion.

CAUTION

  • When placing the projector on a table or shelf, be careful not to put it near the edge.

– The projector could fall due to balance problems, which may cause personal injury or damage to the product. Make sure to use the projector cabinet or stand that fits the projector.

  • When moving the projector, make sure to switch it off and remove the power plug and cords.

– The power cord may be damaged, resulting in fire or electric shock.

  • Do not place the projector on an unstable or vibrating surface such as a wobbly shelf or a slope.

– It may fall and cause injury.

  • Be careful not to tip the projector over when connecting external devices to the projector.

– This may cause personal injury or damage to the projector.

Power

WARNING

  • DISCONNECTING THE DEVICE FROM THE MAIN POWER

– The Power plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

  • The grounding wire should be connected. (Except for devices which are not grounded.)

– Ensure that you connect the grounding cable to avoid electric shock. If it is not possible to ground the unit, have a qualified electrician install a separate circuit breaker. Do not try to ground the projector by connecting it to telephone wires, lightning rods, or gas pipes.

  • The power plug should be inserted fully into the power outlet.

– An unstable connection may cause a fire.

  • Do not place heavy objects on the power cord.

– This may result in fire or electric shock.

  • Never touch the power plug with wet hands.

– This may result in electric shock.

CAUTION

  • Always grab the plug to remove the AC adapter or power cord.

– Otherwise, this may result in a fire or may damage the product.

  • Refrain from constantly bending the power cord of the AC adapter.

– If the power cord is bent excessively for a long period, the cord may break inside. This may result in a fire or electric shock.

  • Place the projector where people will not trip over or step on the power cord to protect the power cord and plug from any damage.

– This may result in fire or electric shock.

  • Do not turn the projector on or off by plugging in the power plug or unplugging it from the power outlet. (Do not use the power plug as a switch.)

– This may result in electric shock or damage to the product.

  • Do not insert a conductor into the other side of the wall outlet while the power plug is inserted into the wall outlet. In addition, do not touch the power plug immediately after it is disconnected from the wall outlet.

– This may result in electric shock.

  • Only use the official power cord provided by LG Electronics. Do not use other power cords.

– This may damage the power cord and result in a fire or electric shock.

  • Connect the AC adapter and the power cord firmly.

– Not doing so may result in a product failure or fire.

  • Do not place heavy objects or put pressure on the power cord and AC adapter and avoid damage.

– This may result in a fire or may damage the product.

When in Use

WARNING

  • Do not place anything containing liquid on top of the projector such as a vase, flower pot, cup, cosmetics, medicine, ornaments, candles, etc.

– This may result in fire or electric shock, or cause injury due to falling.

  • If there is a heavy impact or the cabinet is damaged, switch it off, unplug it from the power outlet, and contact an authorized service center.

– This may result in electric shock.

  • Do not insert pieces of metal such as coins, hairpins, or metal debris, nor flammable materials such as paper or matches into the projector.

– This is to prevent electric shock or fire.

  • Make sure that a child does not swallow the batteries when you replace the old batteries in the remote control with new ones. Keep batteries out of reach of children.

– If a child swallows a battery, consult a doctor immediately.

  • Never open any cover on the projector.

– There is a high risk of electric shock.

  • Do not look directly into the lens when the projector is in use.

– The bright light may damage your eyes.

  • When the lamp is on or has just been turned off, avoid touching the air vent or lamp, because these will be very hot.
  • If there is a gas leak in the room with the projector, do not touch the projector or power outlet. Open the windows for ventilation.

CAUTION

  • Do not place heavy objects on the projector.

– It may fall and cause personal injury.

  • Be careful not to allow any impact on the lens during transport.
  • Do not touch the lens of the projector.

– The lens may be damaged.

  • Do not use any sharp tools on the projector such as a knife or hammer, because this may damage the casing.
  • If no image appears on the screen or no sound is heard, stop using the projector. Switch off the projector, unplug it from the power outlet, and contact our service center.

– This may result in fire or electric shock.

  • Do not drop anything onto the projector or allow anything to bang into the projector.

– High volume may damage hearing.

  • Do not use high-voltage electrical equipment near the projector, (e.g., a bug zapper). This may result in product malfunction.

Cleaning

WARNING

  • Do not spray the projector with water when cleaning. Make sure water does not flow into the projector.

– This may result in fire or electric shock.

  • When smoke or a strange smell is coming out from the projector or a foreign object falls into the projector, please switch it off unplug it from the power outlet, and contact our service center.

– Otherwise, this may result in fire or electric shock.

CAUTION

  • Contact your seller or our service center once a year to clean the internal parts of the projector.

– If you do not clean the projector for a long period, dust will accumulate, which may result in fire or damage to the projector.

  • When cleaning plastic parts such as the projector case, unplug the power first and wipe with a soft cloth. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, automobile or industrial polish, abrasives, wax, benzene, or alcohol as these can damage the projector.
  • This can result in fire, electric shock, or cause damage to the product (deformation and corrosion).
  • This can result in fire, electric shock, or cause damage to the product (deformation and corrosion).
  • Remove the plug from the outlet before cleaning the product.

– Otherwise, this may result in electric shock.

Risk Group 2

CAUTION
Possibly hazardous optical radiation is emitted from this product. Do not stare at the operating lamp. May be harmful to the eye. This label is attached to the bottom of the product and the language may differ.

ANTENNA

WARNING

  • If you are using an outdoor antenna, please install it away from electrical wires to make sure it does not touch any nearby wires even when it falls due to heavy wind.

– Failure to do so may cause electric shock or physical injury.

CAUTION

  • To prevent any water from flowing into the product, install a drip loop in the outdoor antenna wire where it comes indoors.

– Raindrops flowing into the product may cause fire or electric shock.

PREPARATION

The pictures may differ slightly from the actual product.

Accessories
Accessories included with the projector are shown below. Accessories are subject to change without prior notice. New accessories may be added or old ones removed.LG HF65LA Full HD Home Theater-fig 1

  • When connecting an HDMI or USB cable, or connecting a USB flash drive to the HDMI or  USB port, use a product that has a width of 18 mm (0.7 inches) or less and a height of 10 mm (0.3 inches) or less. If the USB cable or USB flash drive does not fit the USB ports of the projector, use an extension cable that supports USB 2.0.LG HF65LA Full HD Home Theater-fig 2
  • When connecting two USB devices at the same time, each one should have bezels less than 8.5 mm (0.3 inches) thick.
  • Use a certified cable with the HDMI logo attached.
  • If you do not use a certified HDMI cable, the screen may not display or a connection error may occur. (Recommended HDMI cable types) – Ultra High-Speed HDMI®/™ cable (3 m (9.8 feet) or less)

Optional Extras

To purchase optional accessories, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Optional accessories are subject to change without prior notice.LG HF65LA Full HD Home Theater-fig 3

Parts and Components

This projector is manufactured using high-precision technology. You may, however, see tiny black dots and/or bright-colored dots (red, blue, or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.

LG HF65LA Full HD Home Theater-fig 4

  1. Due to the high temperature of the vent area, do not get close to the vent area.
  2. Do not touch the lens and mirror when using the projector. The lens may be damaged. (Keep lens away from sharp objects.)
  3. Turn the adjustable leg left or right to adjust the angle.LG HF65LA Full HD Home Theater-fig 5LG HF65LA Full HD Home Theater-fig 6

Using the Joystick Button

You can operate the projector by pressing the button or moving the joystick left, right, up, or down.

LG HF65LA Full HD Home Theater-fig 7

NOTE

  • Place your finger over the joystick button and move it up, down, left, or right. Be careful not to press the joystick button. If you press the joystick button first, you may not be able to adjust the volume level and/or scroll through saved channels.

Adjusting the menu

When the projector is turned on, press the joystick button one time. You can adjust the menu items () by moving the joystick button left, right, up, or down. Move to the desired menu item, and then press the joystick button once to select it.

LG HF65LA Full HD Home Theater-fig 8

Projector Status IndicatorsLG HF65LA Full HD Home Theater-fig 9LG HF65LA Full HD Home Theater-fig 10

Installation

Installation Precautions

  • Place the projector in a well-ventilated environment.
  • To prevent internal overheating, install the projector in a well-ventilated place. Do not place anything near the projector. That may block its air vents. If the air vents are blocked, the internal temperature of the projector will increase.LG HF65LA Full HD Home Theater-fig 12
  • Do not place the projector on a carpet or rug. If the projector’s inlet vent is on the bottom, be careful not to block the vent, and always use the projector on a solid, level surface.LG HF65LA Full HD Home Theater-fig 14
  • Be sure to prevent foreign objects such as paper debris from entering the projector.LG HF65LA Full HD Home Theater-fig 11
  • Leave an adequate open area (30 cm (11.8 inches) or more) around the projector.LG HF65LA Full HD Home Theater-fig 13
  • Do not place the projector in a hot, cool, or humid environment.
  • Do not place the projector in a place where it will easily attract dust. – This may result in fire.
  • Never open any cover on the projector. There is a high risk of electric shock.
  • The projector is manufactured using high-precision technology. You may, however, see tiny black dots and/ or bright-colored dots (red, blue, or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
  • The remote control may not work in an environment where a lamp equipped with electronic ballasts or a three-wavelength fluorescent lamp is installed. Replace the lamp with an international standard lamp for the remote control to work normally.
  • To install the ceiling, attach the ceiling-type bracket to the projector with M4 x 8 mm screws.
  • Do not overtighten the screws. It may damage the case, causing the projector to fall and cause serious injury. (Recommended Torque: 4.34 ~ 6.94 ibf-in (5~8 kgf·cm))

Projection Distance per Screen Size

  1. Place the projector on a sturdy, level surface, together with the PC or audio/ video source.
  2. Place the projector at an appropriate distance away from the screen. The distance between the projector and the screen determines the actual size of the image.
  3. Position the projector so that the lens is at a right angle to the screen. If the projector is not at a right angle, the projected image will look distorted. To correct the distortion, use the Edge Adjustment function.
  4. Connect the power cord of the projector and the connected device to the wall outlet.LG HF65LA Full HD Home Theater-fig 15LG HF65LA Full HD Home Theater-fig 16

The projection distance may vary depending on the installation conditions


 NOTE

  • If the projected image looks distorted or bent, check to see if the screen is installed properly.

Kensington Security System

  • This projector has a Kensington Security Standard connector as an anti-theft mechanism. Connect a Kensington Security System cable as shown below.
  • For more information on installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System.
  • The Kensington Security System is an optional accessory.
  • What is Kensington?

Kensington is a company that provides safety systems for laptops and other electronic devices.

MAGIC REMOTE CONTROL

If the battery low message appears while using the Projector, replace the batteries. As shown in the figure press the top of the battery cover and side it down the cover. insert two new and identical batteries (1.5 V, AA type) with + and – poles pointing in the correct direction in the remote control.LG HF65LA Full HD Home Theater-fig 18

NOTE Do not mix new batteries with old onesLG HF65LA Full HD Home Theater-fig 19LG HF65LA Full HD Home Theater-fig 20

To Register the Magic Remote Control

To use the Magic Remote control, register it with your projector first.

  1. Put batteries into the Magic Remote and turn the Projector on.
  2. Point the Magic Remote at your projector and press the Wheel      (OK) on the remote control.
  3. If the projector fails to register the Magic Remote, try again after turning the projector off and back on.

To Re-register the Magic Remote Control

  1. Press the buttons at the same time, for five seconds, to unpair the Magic Remote with your projector.
  2. Press the Wheel      (OK) button towards the projector to re-register the magic remote control. Pressing and holding the button will let you cancel and re-register Magic Remote at once.

Using the Magic Remote Control

  • Shake the Magic Remote slightly to the right and left or press the (INPUT) buttons to make the pointer appear on the screen.
  • If the pointer has not been used for a certain period or Magic Remote is placed on a flat surface, then the pointer will disappear.
  • If the pointer is not responding smoothly, you can reset the pointer by moving it to the edge of the screen.
  • The Magic Remote depletes batteries faster than a normal remote due to the additional features.LG HF65LA Full HD Home Theater-fig 21

 CAUTION

  • Use the remote control within the specified range (within 10 m (32.8 feet)). You may experience communication failures when using the device outside the coverage area or if there are obstacles within the coverage area.
  • You may experience communication failures depending on the accessories. Devices such as a microwave oven and wireless LAN operate in the same frequency band (2.4 GHz) as the Magic Remote. This may cause communication failures.
  • The Magic Remote may not work properly if a wireless router (AP) is within 1 m (3.2 feet) of the projector. Your wireless router should be more than 1 m (3.2 feet) away from the projector.
  • Do not disassemble or heat the batteries.
  • Do not drop the battery. Avoid extreme shocks to the battery.
  • Inserting a battery in the wrong way may result in an explosion.

USING THE PROJECTOR

Connecting the Antenna or Cable

To watch TV using an indoor/outdoor antenna, connect a wall terminal and the antenna port of the projector using an RF cable (75 Ω). You can watch terrestrial or cable (analog, digital) TV. (The RF cable is sold separately.)LG HF65LA Full HD Home Theater-fig 22

 NOTE

  • Make sure not to bend the copper wire of the RF cable (75 Ω). Turn the input jack to the right to fasten it.
  • Ensure you use a standard coaxial cable (75 Ω, sold separately) when connecting to the projector input.LG HF65LA Full HD Home Theater-fig 23
  • For better image quality in locations where Copper wire signal strength is low, purchase and install a signal amplifier (booster).
  • A signal splitter is required if you want to use two or more projectors through one antenna.
  • If you have any problems when installing the antenna, please consult a suitable retailer or the store where you purchased the antenna.

Focus of the Screen Image

When an image appears on the screen, check if it is in focus and fits the screen properly.LG HF65LA Full HD Home Theater-fig 24

  • To adjust the focus of the image, rotate the focus ring.
  • Make sure the product does not move when adjusting the focus.

Watching With the Projector

  1. When in standby mode, press the (POWER) button to turn the projector on.
  2. Select the (INPUT)      [All Inputs] and select the input signal you want.
  3. Control the projector using the following buttons while watching the projector.LG HF65LA Full HD Home Theater-fig 25
  4. To turn the projector off, press the (POWER) button.

CONNECTING DEVICES

You can connect various external devices to the projectorLG HF65LA Full HD Home Theater-fig 26

MAINTENANCE

Clean your Projector to keep it in optimal condition.

Cleaning

Cleaning the Lens

  • If there is any dust or staining on the lens surface, you must clean the lens.
  • To remove dust or stains on the lens, use a compressed air duster, cotton swab, or soft cloth to gently wipe the lens.
  • Do not wipe the lens while the product is in use or immediately after it has been turned off.
  • When cleaning the lens, do not use a cleanser, automobile or industrial shiner, abrasive, wax, benzene, alcohol, water, etc., as this may damage the product.

Cleaning the Projector Case

  • To clean the projector case, first unplug the power cord.
  • To remove dust or stains, use only a dry, lint-free, nonabrasive cloth to polish the lens.
  • Do not use alcohol, benzene, thinners, or other chemicals, that may damage the case.

SPECIFICATIONSLG HF65LA Full HD Home Theater-fig 27

LG HF65LA Full HD Home Theater-fig 28LG HF65LA Full HD Home Theater-fig 29LG HF65LA Full HD Home Theater-fig 30LG HF65LA Full HD Home Theater-fig 31

  • If an invalid signal is input into the projector, it will not be displayed properly on the screen or a message such as [No Signal] or [Invalid Format] will be displayed.
  • The projector supports the DDC1/2B type as the Plug and Play function (Autorecognition of PC monitor).
  • 1920 x 1080 is recommended as the best picture quality in the PC mode.

Open Source Software Notice Information   

Information

To obtain the source code under GPL, LGPL, MPL, and other open-source licenses, that are contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers, and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com. This offer is valid for three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.LG HF65LA Full HD Home Theater-fig 32

TROUBLESHOOTING

If you experience any of the problems below while using the product, please check the following. There may be no problem with the product. Information on customer service for product problems is available in  (Q. Settings) [General]  [About This Projector] on the projector.

Abnormal Operation

I cannot see some channels.

  • Adjust the position or direction of the antenna.
  • Save the desired channels in (Q. Settings)  [Channels]  [Channel Tuning] or [Channel Manager].

The screen does not appear for some time after power-on.

  • This is because there is a noise-removal process to eliminate any possible noise that may appear during power-on. This does not mean the product is defective.

The pointer of Magic Remote does not appear on the screen.

  • Your Magic Remote may have run out of batteries.
    Replace the batteries and register your Magic Remote again following the instructions shown in the MAGIC REMOTE CONTROL of the Owner’s Manual.
  • This only applies to models that support the Magic Remote.

I cannot turn on the Projector.

  • Please make sure your projector power plug is correctly connected to the outlet.
  • If you are using a multi-outlet, check if it is working properly.
  • Try to power on using the button on your projector set.

It says there is no signal on the screen.

  • Make sure that the coaxial cable or HDMI cable is correctly connected to your projector.
  • Go to choose the connected input.
  • Check if your external device, such as the set-top box or Blu-ray player, is turned on.

It does not work when I connect a USB device.

  • Check that the USB and USB cable versions are 2.0 or higher.

Screen Problems

First of all, perform a  (Q. Settings)[Picture]    [Picture Test] to check for any abnormalities in the projector. If you are using a set-top box, turn it off, and then turn it back on. Make sure that the set-top box is correctly connected to your projector.

The screen overlaps or there are stripe patterns on all channels or a specific channel.

  • Turn the antenna toward the broadcasting station or connect the antenna correctly by the How to Connect an Antenna section.

The screen shakes after the momentary appearance of vertical/horizontal lines and net pattern.

  • Stop using items such as wireless telephones, hairdryers, electrical drills, etc. The problem is caused by high-frequency electronic devices such as another projector or strong electromagnetic sources.

A digitally broadcast program stops or its screen is broken.

  • This happens when a signal is weak or reception is unstable. Adjust the antenna direction or check the cable connection.
  • If the signal strength is too low in (Q. Settings)  [Channels]

 [Channel Tuning]  [Manual Tuning], contact the broadcasting station or management office to have the signals checked.

I cannot see digital broadcasts even though I am using cable television.

  • Check your subscription information with your cable television service provider or ask for the signal to be checked. (Some products do not provide digital broadcasts.)

There is a difference in picture quality for each channel.

  • XX-0 channels are analog channels. It is recommended for watching digital channels such as XX-1.
  • Run [Picture Test] first. If it is normal, there may be a problem with the broadcast signal.

I see vertical lines in all four directions on the screen, or colors are blurred when I try to connect to HDMI.

  • (Q. Settings)[Picture]    [Aspect Ratio Settings]  [Just Scan] Set [Just Scan] to [Off]. [Just Scan] shows you the original image as it is. You may see noise in all four directions on the screen if the signal contains noise.

The screen is blank or the image is blurred when an HDMI cable is used.

  • Check that the HDMI® cable meets the required standards. If it is not a certified HDMI® cable, the screen may flicker or may not display anything.
  • Check that the cable is properly connected. Improper connection may cause screen flicker.

Sound Problems

First of all, perform a  (Q. Settings) [Sound] [Sound Test] to check for any abnormalities in the projector. If you are using a set-top box, turn it off, and then turn it back on. Make sure that the set-top box is correctly connected to your projector.

The screen is fine, but it does not play any sound.

  • Try another channel. (Q. Settings)  [Sound]  [Sound Out] Check whether the [Sound Out] is set to [Internal Projector Speaker]. If you use a set-top box, there will be no sound if you have set the volume of the set-top box or your projector to 0 or enabled Mute. Set the volume to an appropriate level.

The stereo sound is not clear on an analog channel, or there is no sound from one of the speakers.

  • Applies only in countries where sound multiplex broadcasting is available. Wheel (OK) or OK Select [MONO] in Multi Audio if you are out of range or sound multiplex broadcasting is not stable.
  • (Q. Settings) [Sound]     [Sound Mode Settings]  [Balance] Adjust the balance as necessary with the Navigation button in [Balance].

The TV sound is not synchronized with the picture, or the sound sometimes breaks up.

  • If this happens on only some of the channels, it may be caused by the broadcasting company’s transmission signal. Please have your broadcasting services provider (wired/cable) diagnose the problem.
  • If all channels are out of sync, go to (Q. Settings) [Sound]     [AV Sync Adjustment] and adjust the sync.

The volume changes when I change the channel.

  • The volume of different broadcasting stations’ transmission output may vary.
  • (Q. Settings) [Sound] [Auto Volume] Set [Auto Volume] to [On].

The sound does not work or only the background music is played in some programs. (Programs produced for export by broadcasting companies)

  • Wheel (OK) or OK            
  • Set your language preference in [Audio Language].

The sound does not play when I connect to the HDMI/USB port.

  • Check that you are using a high-speed HDMI® cable.
  • Check that the USB and USB cable versions are 2.0 or higher.
  • Use a normal music file (*.mp3, *.wav, *.ogg, *.wma).

PC Connection Problems

The screen remains blank after it is connected to a PC.

  • Check that the PC is properly connected to the projector.
  • Turn the projector off and back on using the remote control.
  • Restart the PC with the projector on.
  • Check that the current screen resolution supports the PC input.
  • To use dual monitors, check that the PC or notebook supports dual-monitor mode.
  • Reconnect the high-speed HDMI cable.
  • If you have connected the RGB output port of your PC to the HDMI input port or your projector. You need an RGB to HDMI gender. You will not see anything on the screen if you use an HDMI to RGB gender.

The sound does not play when the PC is connected to an HDMI cable.

  • Contact your video card manufacturer to check the HDMI audio output. (Video cards designed for use with DVI format files need to be connected separately with an audio cable.)

The screen is cut off or moved to one side after it is connected to a PC.

  • Set to a resolution that supports the PC input. (Reboot your PC after changing the resolution.)

[Photo & Video] Movie Playback Problems

For more information about supported files, see “PLAY OTHER DEVICE FILES”.

I cannot find a file in the [Photo & Video].

  • Check that the files on the USB storage device can be read by a PC.
  • Check that the file extension is supported.

I get a message saying “This file is not supported” or the sound is playing normally but the video is not.

  • Check that the file plays without any problems on a PC’s video player. Also, check for file damage.
  • Check that the file extension is supported.
  • Check that the resolution is supported.
  • Check that the video codec is supported.
  • Check that the frame rate is supported.

I get a message saying “This audio is not supported” or the video is playing normally but the audio is not.

  • Check that the file plays without any problems on a PC’s video player. Also, check for file damage.
  • Check that the file extension is supported.
  • Check that the audio codec is supported.
  • Check that the bit rate is supported.
  • Check that the sample rate is supported.
  • Check that the audio channel separation is supported.

I cannot see the subtitles.

  • Check that the file plays without any problems on a PC’s video player. Also, check for file damage.
  • Check that the video and subtitle files have the same name.
  • Also, check that both the video file and the subtitle file are in the same folder.
  • Check that the subtitle file format is supported.
  • Check that the language is supported. (You can check the language of the subtitle file by opening the file in Notepad.)
  • If subtitles encoding is incorrectly set, subtitles may not be displayed properly. Select the control panel at the bottom of the video playback screen and change the [CODE PAGE] value.
  • If you play a video file stored on another device by using the content-sharing feature, subtitles may not be available depending on the program you use.

Network Connection Problems

You can check the network connection status as shown below.

When X appears next to the projector

  • Check the projector or the AP (Router).
  • Check the connection status of the projector, AP (Router), and Cable Modem.
  • Power off and power on in the following order;
  1. The Cable Modem, wait for the Cable Modem to reset.
  2. The AP (Router), waits for the AP (Router) to reset.
  3. The projector.
  • If you are using a wireless connection, change the SSID (Network name) and wireless channel of AP (Router).
  • If you are using a static IP, enter the IP directly.
  • Contact internet service providers or AP (Router) companies.

   When X appears next to Gateway

  • Check the AP (Router) or consult your Internet service provider.
  • Unplug the power cord of the AP (Router) and cable Modem, and wait 10 seconds. Reapply power.
  • Initialize (Reset) on the AP (Router) or Cable Modem.
  • Contact internet service providers or AP (Router) companies.
  • Check the AP (Router) manufacturer’s website to make sure your router has the latest firmware version installed.

When X appears next to the DNS

  • Check the AP (Router) or consult your Internet service provider.
  • Unplug the power cord of the Cable Modem or the AP (Router), and wait 10 seconds. Reapply power.
  • After the Cable Modem or AP (Router) has Initialized (Reset), try to reconnect.
  • Check that the MAC address of the projector/AP (Router) is registered with your Internet service provider. (The MAC address displayed on the pane of the network status window should be registered with your Internet service provider.)

LG Account Problems

In some countries, access to the website (www.lgappstv.com) may be restricted.

I have already signed up for the projector. Do I still have to sign up again at the website (www.lgappstv.com)?

  • If you have already signed up on your projector, you do not have to sign up again on the website. You can sign into the website by using the same ID and password and entering the additional information to complete the email verification process.

Is it possible for the family members to use different IDs on the same projector?

  • You can register multiple IDs per projector.

I forgot my ID/Password. What should I do?

  • You can initialize the password through E-mail when you select FORGOT PASSWORD? on the sign-in screen.
  • If you signed up on a PC, you can find your ID/Password on the website (www.lgappstv.com).

Contents Problems

I cannot see any content in HOME.

  • This feature is available in certain countries only.

You may not be able to see the content if the service country setting has been changed. Change to the service country you are going to use the service from in  (Q. Settings)  [General]  [Location]  [LG Services Country].

  • You may not be able to view content that has been deleted. Please reinstall the appropriate app.
  • The type of supported content differs by country.
  • The content offerings are subject to change or interruption by the service provider.

Internet Browser Problems

Some parts of a particular website are not visible when I am using the Internet.

  • The [Web Browser] supports only HTML5 media and not Flash Plug-in.
  • The [Web Browser] does not support plug-in installation.
  • On the [Web Browser], it may not be possible to play media files in formats other than JPEG/PNG/GIF
  • You cannot save attachments or images.

The Internet browser automatically shuts down when I visit a website.

  • The Internet browser may be forced to shut down if the available memory size is not sufficient to accommodate the image information for a website.

FAQS About LG HF65LA Full HD Home Theater

LG home theater runs on what voltage?

200- 240V~, 50/60Hz.

What is the LG home entertainment system’s wattage?

330W

Why won’t my LG home theater start up?

Examine the power outlet and cable

Is Bluetooth available on LG home theater?

Bluetooth audio without a wire.

What power output is ideal for a home theater system?

It needs to be at least 100 W.

How much electricity do speakers for home theaters require?

50 watts

What is the amp need for a home theater?

15 amps

How much energy does a receiver for home theater use?

If it is a surround-sound model with 5.1 channels or more, it will probably be at least 120 watts.

What speakers in a home theater are the most crucial?

center-channel speakers

Are amplifiers required for home theater?

if you’re a genuine music lover and audiophile. Buying an amplifier can be a smart move.

How do I link my laptop to my LG home theater?

the use of an HDMI cable

For more manuals by LG, Visit Manualsdock

[embeddoc url=”https://manualsdock.com/wp-content/uploads/2023/09/LG-HF65LA-Full-HD-Home-Theater-Owner-Manual.pdf” download=”all”]

Leave a Comment