Skullcandy Dime 3 In-Ear Wireless Earbuds User Guide

Skullcandy Dime 3 In-Ear Wireless Earbuds

User Guide

Auto Power – On/Off

• Auto On – Remove buds from Case
• Auto Off – Place buds into Case

Manual Power – On

• Off Mode Either bud

Manual Power – Off

• On Mode Both earbuds

Manual Pairing Mode

• On Mode Either bud

Pair New Device

• Voice Prompt – “Ready to Pair”
• Available Device – “Dime 3”

Play/Pause, Answer Call

• While On Either bud

Volume Up
Either Earbud

Volume Down
Either Earbud

Stay-Aware Mode On/Off
Either Earbud

Activate Voice Assistant
Left Earbud or Right Earbud

EQ Switch

• On Mode
• Connected

Re-Sync Earbuds
Both Earbuds

• While On
• Bluetooth Disconnected

Reset the Paired Device List
Both earbuds

• While ON
• Bluetooth Disconnected

Charge Earbuds
Earbud LEDs turn RED to indicate charging.

Charge the Case

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED Compliance Statement
This device contains license-exempt transmitters)/receivers) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1 )This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the head.

ISED SAR Compliance Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the head.

1-YEAR GLOBAL WARRANTY

Skullcandy products are backed by a 1-year warranty. If it doesn’t work the way we promised, we’ll make it right. For claims, questions, or Terms & Conditions: U, S. & Canada only: visit Skullcandy.com/warranty or call 1-888-MYSKULL All other countries: visit Skullcandy.com/support/international-support Many electrical items can be repaired or recycled, saving natural resources and the environment. If you do not recycle, electrical equipment will end up in landfills where hazardous substances will leak out and cause soil and water contamination – harming wildlife and also human health.

To remind you that old electrical equipment can be recycled, it is now marked with a crossed-out wheeled bin symbol. Please do not throw any electrical equipment (including those marked with the crossed-out wheeled bin symbol) in your bin. Many Local Authorities will have containers that collect batteries for recycling. Public buildings and your workplace may also have containers. If you do not recycle, batteries will end up in landfills where hazardous substances will leak out and cause soil and water contamination – harming wildlife and also human health.

Batteries containing hazardous materials such as mercury (Hg), cadmium (Cd), or lead (Pb) are marked with their chemical symbols as well. This symbol means that according to local laws and regulations, the battery shall be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities or return it to the purchase location for recycling or disposal.

For more Manuals by SKULLCANDY, visit MANUALSDOCK

FAQS About Skullcandy Dime 3 In-Ear Wireless Earbuds