Saramonic Blink 100 B5 Clip-On Wireless Mic System User Manual

Saramonic Blink 100 B5 Clip-On Wireless Mic System

Statement

Please read this manual carefully before using it and strictly operate and store it by the instructions. Please save the manual for your future reference. If you need further assistance than the user manual, please consult your retailer for help or email us: info@saramonic.com

Cautions

1. Disintegration of this device by non-professionals is strictly prohibited.
2. Please keep it away from heat sources such as heaters or ovens.
3. Do not remove the battery without professional’ help.
4. Please clean the device with only a soft, dry cloth.
5. When using and storing, please pay attention to dust and moisture.
6. For the best pick-up pattern, do not hold your hand against the microphone capsule cover.

Available Kits

General Introduction

Saramonic Blink100 is an ultra-compact and portable 2.4GHz wireless microphone system, compatible with smartphones, tablets, DSLR cameras, and camcorders. It features automatic pairing and selectable noise cancellation, delivering broadcast-quality sound. Blink100 is ideal for live streaming, vlogging, mobile journalist,m and more.

Product Structure

Wireless Transmitter Blink100 TX

1. Status indicator
2. Power/Mute button
3. + -/NR button
   Press the +/- button to adjust the mic gain. (The setting is retained even after the power is turned off.) Press and hold or continuously press “+”/ “-” to adjust mic gain to maximum/ minimum, the indicator flashes blue twice (flashes green twice in noise cancellation mode). Press the NR button (press both the “+” and “-” buttons at the same time) to turn on/off noise cancellation. (Default setting is off.)
4. Belt clip
5. Built-in microphone
6. USB-C charging port (DC 5V)
   Use the supplied USB-C charging cable to charge the unit.

Wireless Receiver Blink100 RX

1. Status indicator
2. Power button
   Press and hold the power button for 2s to turn it on/ off.
3. LINE OUT jack
   Connect the Blink100 RX to a smartphone, tablet, camera, recorder, or mixer with the supplied output cables.
4. USB-C charging port (DC 5V)
   Use the supplied USB-C charging cable to charge the unit.
5. Belt clip

How to use

For the Blink100 B1/B2 kit

1. Press and hold the power button for 2 seconds to turn on the transmitter/receiver.
2. The transmitter and receiver will be successfully paired within 10s.
3. You are ready to record.

Note
Due to the 2.4GHz wireless frequency, the signal can be easily attenuated. Please try to avoid obstacles, such as walls and buildings, and avoid proximity to devices with 2.4GHz signals, such as high-power Wi-Fi antennas, radios, etc.

Specifications

Packing list

Blink100 B1

• Blink100 TX Transmitter ×1
• Blink100 RX Receiver ×1
• 3.5mm TRS to TRS Output Cable for Cameras ×1
• 3.5mm TRS to TRRS Output Cable for Smartphones ×1
• USB-C Charging Cable ×2
• Fur Windshield ×1

Blink100 B2

• Blink100 TX Transmitter ×2
• Blink100 RX Receiver ×1
• 3.5mm TRS to TRS Output Cable for Cameras ×1
• 3.5mm TRS to TRRS Output Cable for Smartphones ×1
• USB-C Charging Cable ×3
• Fur Windshield ×2

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISEDC Warning
This device complies with the Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

For more Manuals by SARAMONIC, visit MANUALSDOCK

FAQS About Saramonic Blink 100 B5 Clip-On Wireless Mic System