Mattress Firm 600
About Mattress Firm
Mattress Firm is a U.S.-based specialty retailer of mattresses and bedding accessories. The company was founded in 1986 and is headquartered in Houston, Texas. Mattress Firm operates over 2,500 stores across the United States, making it one of the largest mattress retailers in the country. The company offers a wide range of mattresses from leading brands such as Serta, Sealy, Simmons, and Tempur-Pedic, as well as its own private-label brands. In addition to mattresses, Mattress Firm also sells bedding accessories such as pillows, sheets, and mattress protectors.
Adjustable Base setup guide
STEP 1: Remove the top of the shipping carton. Verify contents; inspect for damage.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING: DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE.
- x6 – Pin-adjustable Legs
- x1 – Remote Control (varies according to base type)
- x4 – 3-Inch Carriage Bolts and Nuts
- x2 – T-Spacers
- x1 – Mattress Retainer
- x2 – Center Support Brackets
- x3 – AAA Batteries
- x1 – WRENCH
STEP 2: Cut the zip-tie from the electrical power supply. Cut (2) zip-ties and remove mattress retainer (set aside) (FIGURE 1).
CAUTION: BE CAREFUL USING SHARP INSTRUMENTS. INJURY IS POSSIBLE IF TOOLS ARE NOT USED PROPERLY.
WARNING: PINCH POINT WARNING! KEEP HANDS AND FINGERS CLEAR WHEN SLIDING BASES TOGETHER.
STEP 3
- Carefully lift the base head section out of the shipping carton and place it on a clean surface (FIGURE 2).
- Remove the divider from the shipping carton.
- Carefully lift the base foot section out of the shipping carton and place adjacent to the head section (FIGURE 2).
- Slide head and foot sections together making sure to align mounting holes (center of base sections) (FIGURE 2).
STEP 4
- Place a T-Spacer in between the mounting points (each side of the base). Line up the holes in the T-Spacers with the holes in the mounting points (FIGURE 3).
- Place a center support bracket over the mounting points on each side of the base. Insert carriage bolts through the square holes in the center support bracket. Install nuts on carriage bolts (FIGURE 3). HAND TIGHTENS.
- After all, the hardware is installed, tighten all nuts using the provided wrench.
STEP 5
- Route FOOT MOTOR CABLE underneath the base frame and connect to HEAD MOTOR CABLE (FIGURE 4).
- 600 MODEL ONLY – Route FOOT MASSAGE MOTOR CABLE underneath the base frame and plug into the control box (FIGURE 4).
- Extend the electrical power cord out the head end of the base.
WARNING: POWER CORDS MUST NOT INTERFERE WITH ANY ADJUSTABLE BASE MECHANISMS.
STEP 6
- Screw (4) legs into the threaded inserts at the corners of the base frame (FIGURE 5).
- Screw (2) legs into the threaded inserts of the center support brackets (FIGURE 5).
- Push pin in to adjust leg height (6 inches to 10 inches).
- Note: When adjusting legs, make sure base sets level on floor.
STEP 7: Rotate the base over onto its legs. Remove the remaining packaging.
WARNING: DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE.
STEP 8
- Install (3) batteries in the remote control.
- Plug the power cord into a power outlet. Note: An electrical surge protection device is recommended (not included).
- Operate remote control to test base functions (FIGURE 6) (see separate Syncing Guide).
STEP 9
- Lower base to a flat position.
STEP 10
- Install the mattress retainer at the foot end of the base.
- Place one end of the mattress retainer into the outside hole of the left insert and place the other end into the outside hole of the right insert (FIGURE 7).
STEP 11: Place the mattress on the base to complete assembly.
Note: If the adjustable base will not operate, refer to the Troubleshooting section of the owner’s manual. To download a copy of the owner’s manual, visit https://lpadjustablebeds.com/om/mattressfirm or call Mattress Firm at 844-628-8376.
To register your adjustable base, please go to https://lpadjustablebeds.com/register or call Mattress Firm at 844-628-8376.
FAQs About Mattress Firm 600 Setup
How can I reset my adjustable mattress firm base?
To reset the electronic components, unplug the base for a minute. Try plugging the bed foundation into a different outlet or checking the outlet with a functional device (a grounded, electrical surge protector is recommended).
Why isn’t my remote for the adjustable bed working?
Your batteries may be running low if your remote doesn’t function. Try replacing the batteries first. If that doesn’t work, see if any dirt or debris is obstructing the remotes or the bed’s sensors. The remote can also be reset by pressing and holding the power button for ten seconds.
How long does a mattress take to adjust?
Although 30 days is the typical recommendation, the length of time may vary based on the sort of mattress that was bought. Innerspring types, for instance, are renowned for adjusting more quickly although they can potentially take up to 4 weeks.
Can an adjustable mattress be turned over?
As opposed to mattresses on flat foundations, mattresses on adjustable bases move more frequently and should be rotated on a regular basis. For users of adjustable bases, preventing mattress degradation is essential.
What should you do if the remote’s buttons are broken?
Verify that none of the remote’s buttons are stuck or jammed. The battery connectors for the remote control could be unclean. Place the batteries back into the remote control after removing them and use a cotton bud or soft cloth to wipe the remote control terminals with a tiny solution of alcohol.
What occurs if I use my mattress before 24 hours have passed?
In actuality, breaking the 24-hour guideline and sleeping on a decent mattress a few hours after unboxing shouldn’t harm it. The main purpose of the guideline is to ensure that you have a nice night’s sleep on your mattress because the bed isn’t particularly comfortable while it’s still expanding.
Why is it necessary to wait 24 hours before using a new mattress?
After unwrapping, the majority of boxed mattresses ought to have fully inflated in 12–24 hours. They must reintroduce air into their foam layers, which were crushed and evacuated during packaging, for this reason.
Is it necessary to wait 24 hours before using a new mattress?
It might take anything from a few hours to up to 48 hours to fully expand, depending on the situation. We always err on the side of caution and eyeball it. It is okay to sleep on your mattress after it appears fluffy and soft, which normally occurs on the first night.
Why is the buzzer on my adjustable bed?
The remote control can simply not have enough power due to a set of failing batteries. Alternatively, the problem can be that the wall outlet isn’t functioning properly or that the power cord for the adjustable bed isn’t entirely plugged in.
Exists a break-in period for new mattresses?
It is typically advised to give your mattress at least a week to get used to your body. During this time, sleep on your new mattress every night to help it loosen and stretch as needed. A week-long break-in period is advised unless your mattress is very uncomfortable for sleep.
For more manuals by Mattress Firm, visit ManualsDock