Jensen MPR210 AM-FM Receiver with Bluetooth and Fixed Face Owner Manual

Jensen MPR210 AM-FM Receiver with Bluetooth and Fixed Face

About Jensen 
The JENSEN ® name is a true powerhouse in the world of automotive and consumer electronics, and the brand is an American staple and is unequivocally an automotive and household name. The products behind the Brand are from expert leading-edge technology through aggressive research and development, advanced engineering, and a firm dedication to emerging technologies.

Preparation

Please read the entire manual before installation.

Before You Start

• Disconnect the negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt, or excessive vibration.

Wiring Diagram

Control Locations

1. Power
2. Mute
3. Voice Control
4. Volume Knob
5. Bluetooth Talk
6. USB Port
7. Auxiliary Input
8. Reset
9. Preset 6 / Folder Up
10. Preset 5 / Folder Down
11. Preset 4 / Random
12. Preset 3 / Repeat
13. Preset 2 / Intro
14. Preset 1 / Play/Pause
15. Mode
16. Band/Display
17. Tune-Up
18. Tune Down

General Operation

• Power On/Off:
  Press the button to turn the unit on. Press again to turn the unit off.
• Changing Modes:
  Press MODE to select between Radio, USB, Bluetooth, and AUX. Modes of operation are shown in the display.
• Volume:
  Adjust the volume using the volume knob (00-40).
• Mute:
  Press to silence the audio. Press again to resume listening at the previously selected volume.
• Auxiliary Inputs:
  Insert a 3.5mm cable in the unit’s front AUX port.
• Reset:
  Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located on the front panel.
• Setting the Clock:
  With the unit on, long press DISP to display clock time. Press and hold DISP until the hours or minutes begin to flash, then release. Rotate the volume knob to adjust the time. Long press DISP to finish the clock setting.
• Display:
  Press DISP to toggle display between various displayed information.
• Audio / Menu:
  Press the volume knob momentarily to select between audio functions.
  Press and hold the volume knob for more than two seconds to select between the menu functions.
  Rotate the volume knob left/right to adjust or activate the desired function/audio.

AM/FM Tuner Operation

• Seek Tuning:
  Press TUNE or TUNE to seek the previous or next strong station.
• Manual Tuning:
  Press and hold TUNE or TUNE to enter manual tuning mode, then press TUNE or TUNE momentarily to change the radio frequency up or down one step at a time. Press and hold TUNE or TUNE to advance quickly.
• Band:
  Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to six presets can be programmed
  for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.
• Storing Presets:
  Up to 18 FM and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear on the display.
• Recalling Presets:
  Preset stations can be recalled at any time by pressing the corresponding preset button.
• Automatically Store:
  Press and hold MENU for more than 2 seconds, then press DISP to store 18 FM stations and 12 AM stations automatically.
• Preset Scan Stations:
  Touch PS to recall each preset station that has been stored in memory for each band.
  (Available with the Dual Smart Remote App only)

USB Operation

• Playing MP3 Files:
  To play MP3 files, insert a USB device containing MP3 files.
• Track Select:
  Press TUNE to skip to the beginning of the next track.
  Press TUNE to skip to the beginning of the previous track.
• Fast Forward and Reverse:
  Press and hold TUNE or TUNE to fast forward or reverse a track.
• Pause:
  Press to temporarily stop USB playback. Press again to resume playback.
• Folder Access:
  Folders can be found by pressing Folder Up or Folder Down. About one second after the folder name is displayed, the first file under the selected folder will be displayed and playback will begin.
• Repeat:
  Press RPT to toggle between RPT ALL and RPT ONE.
• Random:
  Press RDM to play tracks in random order; press again to cancel the RDM function.
• Intro:
  Press INT to play the first 10 seconds of each track; press again to cancel the INT function.

Bluetooth Operation

• Preparation:
  Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.
• Pairing a New Device:
  The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details.
  The device’s name is “JENSEN Media Player”.
  The Bluetooth passcode is “1234”.
  Note: The head unit can be in any mode of operation when pairing is performed.
• Streaming Audio Troubleshooting:
  The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:
  • Press to skip to the next available audio track.
  • Press to skip to the previous audio track.
  • Press to toggle between play and pause during playback.

Troubleshooting

Limited One-Year Warranty

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

• Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
• Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equally new, renewed, or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.

Who is covered?

This warranty is extended to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U.S.A.

What is covered?

This warranty covers all defects in material and workmanship in this product.
The following are not covered:

• software, installation/removal costs,
• damage resulting from accident,
• misuse,
• abuse,
• neglect,
• product modification,
• improper installation,
• incorrect line voltage,
• unauthorized repair or failure to follow instructions supplied with the product,
• or damage occurring during the return shipment of the product.

Specific license conditions and copyright notices for the software can be found at www.dualav.com.

What to do?

1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.
4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:
   • Call us toll-free at 1-866-382-5476
   • E-mail us at cs@dualav.com

Exclusion of Certain Damages:

This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed.

No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental, or consequential damages.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specifications

FM Tuner:

• Tuning range: 87.5MHz-107.9MHz
• Usable sensitivity: 8.5dBf
• 50dB quieting sensitivity: 10dBf
• Stereo separation @ 1kHz: >30dB Frequency response: 30Hz-13kHz

AM Tuner:

• Tuning range: 530kHz-1710kHz
• Usable sensitivity: <42dBu
• Frequency response: 30Hz-2.2kHz

General:

• Speaker output impedance: 4~8 ohms
• Line output voltage: 2 Volts RMS Dimensions: 7″ x 2″ x 2″ (178 x 50 x 50 mm)

Design and specifications are subject to change without notice.

FAQS About Jensen MPR210 AM-FM Receiver with Bluetooth and Fixed Face

For more manuals by JENSEN, Visit Manualsdock