iLive IHTB159B Home Theater System User Guide

iLive IHTB159B Home Theater System

Safety Instructions & Warnings

Important Safety Instructions

• Read these Instructions.
• Keep these Instructions.
• Heed all Warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install by the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding – type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long periods.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

FCC Warnings
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference  by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Battery Warnings

• WARNING: Do not ingest the battery, Chemical Burn Hazard.
• If the remote control supplied with this product contains a coin/button cell battery and the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside and part of the body, seek immediate medical attention.
• CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
• WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries.
• The battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
• Do not mix old and new batteries.
• Completely replace all old batteries with new ones.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
• Batteries should be recycled or disposed of as per state and local guidelines.

Additional Warnings and Precautions

• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT, AND FULLY INSERT.
  The mains plug is used as a disconnect device and it should remain readily operable during intended use. To disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
• CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• WARNING: Use of this unit near fluorescent lighting may cause interference regarding the use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
• WARNING: Shock hazard – Do Not Open.
• Caution and marking information is located at the rear or bottom of the apparatus.
• WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing.
• Objects filled with liquids, such as vases, shall not be placed on the apparatus.

Features

• Bluetooth Wireless – range 60 ft.
• Voice prompts announce speaker functions
• Optical audio input
• HDMI audio input
• 6, 5.1 surround sound audio inputs
• 2 stereo audio inputs

Includes

• Subwoofer (main unit)
• 32″ sound bar with 4 satellite speakers
• Remote control: requires CR2025 battery (included)
• Optical audio cable
• 3 RCA stereo audio cables
• 3.5mm to RCA audio cable
• AC/DC power adapter
• Wall mount hardware and instructions

Setup

Power
Plug the AC/DC power adapter (included) into a standard wall outlet and the DC power input on the rear of the subwoofer.

Connect Satellite Speakers
Connect each speaker wire with the corresponding port on the rear of the subwoofer. Be sure to match the plugs to the correct port or the speakers will not function properly.

Wall Mount Bracket Installation

Orientation

Subwoofer Front View

Subwoofer Rear View

Remote

Functions

Note
When using the remote, be sure to aim at the remote signal receiver located on the front of the subwoofer.

Power
Press to turn the system ON or OFF.

Mute
Press to mute the volume.

Bluetooth
Press to switch to Bluetooth Mode

Optical
Press to switch to Optical Mode.

HDMI
Press to switch to HDMI Mode.

Aux
Press to switch to Aux In (RCA) Mode.

5.1CH
Press to switch to 5.1 Surround Sound Mode. Press and hold for 5 seconds to turn voice prompts ON/OFF.

Volume-/+
Press to adjust the volume for all speakers.

Pair/Play/Pause
Press and hold to begin pairing to a Bluetooth device. Press to play or pause the selected track (BLUETOOTH).

Skip Back/Fwd
In Bluetooth Mode, press to skip the selected track.

Center/Sub/Surround
Press to adjust the volume for individual speakers.

Remote Batteries

Requires 1 CR2025 battery (pre-installed).

Bluetooth Wireless

Pairing & Playing Audio

1. When the system first powers ON it defaults to Bluetooth Mode and is ready to pair automatically. When pairing, remain within 3 feet of the Bluetooth device.
2. Using the controls on your Bluetooth device, select IHTB159 in the Bluetooth Settings to pair. If need be, refer to the user’s manual for your specific device for more information.
3. When successfully paired, a voice will announce, “Bluetooth is connected.” Your Bluetooth device will now be heard through the speaker.
4. Use the controls on the connected Bluetooth device to select and play audio. Use the subwoofer controls or the connected Bluetooth device to play, pause, skip, and adjust the volume level.

After initial pairing, the speaker will automatically connect to the last Bluetooth device used whenever it is in Bluetooth Mode. If your device should become unpaired or you find it is unable to connect, press & hold the Pair button to enter Pairing Mode. The blue pairing indicator will flash quickly, a voice will announce, “Bluetooth is connecting,” and you can then connect to the speaker manually.

Learn Feature

What Is the Learn Feature?
The Learn feature captures remote commands from your television remote and teaches your soundbar to operate when these commands are pressed. Power, volume, and mute are a few examples of commands that the bar speaker can learn.

Why Use the Learn Feature?
Teaching the bar speaker remote commands will reduce the number of remotes needed, save time searching for remote codes, and improve the ease of operation.

Note
Not all functions of the sound bar will be available through your remote control, such as bass and treble. Use the included remote for these functions. While your IHTB159 soundbar can learn most IR protocols, not all can be programmed.

Using the Learn Feature

1. With the power Off, press the Play/Pause/Pair/Learn button on the unit. An indicator will flicker red.
2. Press the button you desire to be learned on the included remote. For example: Volume +
3. The red light will continue to flicker, and another indicator will display a blue light.
4. Press the corresponding button on your remote.
5. The red light will continue to flicker, and another indicator will display a green light.
6. When the green light turns off, the button command is saved.
7. The programmed button on your remote will now be able to control your sound bar.
   Note
   It is necessary to program each button i.e. channel and volume + and – separately.
8. To start over, press and hold the Play/Pause/Pair/Learn button for 5 seconds. If the soundbar has failed to learn a command, the Red lights will flash and another indicator will display a blue light. Please try again with a different remote.

Audio Inputs

HDMI
If your television has an HDMI port with an Audio Return Channel (ARC), you can connect to the HDMI input on the subwoofer. An HDMI connection is the easiest way to connect the stereo system to your television. Your TV must have HDMI-ARC for this audio connection to function. A regular HDMI port is not equivalent to HDMI-ARC. Requires a TV with HDMI-ARC and a HDMI cable (not included).

1. Using a standard HDMI cable, connect your television’s HDMI-ARC port to the HDMI input on the subwoofer. Depending on the TV, ARC may need to be enabled through the Audio or Source settings menu.
2. With the unit powered ON, select HDMI Mode through the Source button on the subwoofer or the HDMI button on the remote. A voice prompt and a solid purple light will indicate that HDMI Mode has been selected.

Digital Optical Audio

Requires a device with an Optical audio output and a Digital Optical audio cable (included).

1. Using a Digital Optical Audio Cable, connect your media player’s Optical output to the Optical input on the subwoofer.
2. With the unit powered ON, select Optical Mode through the Source button on the subwoofer or the Optical button on the remote. A voice prompt and a solid orange light will indicate that Optical Mode has been selected.

Important tips for optical audio

• The optical output source should be set to output PCM or Optical Audio and not Dolby Digital.
• Use the correct optical audio cable and make sure that it is firmly seated in both source and subwoofer sockets.
• Optical audio output is activated from the audio source (a red light should be visible from the optical socket). It may be labeled SPDIF in the settings menu of the source.

Audio Inputs

6 Port 5.1 Surround Sound RCA Inputs (5.1 CH)
If your TV, DVD, or other media player has 6 ports of audio output, use the 6 lower audio inputs on the rear of the subwoofer for 5.1 surround sound audio. Requires 3 RCA stereo audio cables (included).

1. Using an RCA stereo audio cable, connect your media player’s Surround Sound stereo outputs to the Surround Sound inputs on the subwoofer. When connecting the audio cables, match the colored plugs to the same colored ports.
2. With the unit powered ON, select Surround Sound Mode through the Source button on the subwoofer or the 5.1CH button on the remote. A voice prompt and a solid white light will indicate that Surround Sound Mode has been selected.

2 Port Stereo RCA Inputs (Aux)
If your TV, DVD, or other media player has only 2 ports of audio output, use the top 2 audio inputs (Left/Right channel) on the rear of the subwoofer for stereo audio. Requires an RCA stereo audio cable (included).

1. Using an RCA stereo audio cable, connect your media player’s RCA stereo outputs to the RCA stereo inputs on the subwoofer. When connecting the audio cables, match the colored plugs to the same colored ports.
2. With the unit powered ON, select Aux Mode through the Source button on the subwoofer or the Aux button on the remote. A voice prompt and a solid green light will indicate that Aux Mode has been selected.

Customer Support

Contact Information

• Website: www.iLiveElectronics.com
• Email Support: prodinfo@dpiinc.com
• Email Parts: partsinfo@dpiinc.com
• Phone Support: 1-888-999-4215

Warranty
For Warranty Information and the most up-to-date version of this User’s Guide, go to: www.iLiveElectronics.com

International Support
To download this User’s Guide in English, Spanish, and French, or to get answers to frequently asked questions, visit the support section at: www.iLiveElectronics.com

For more Manuals by ILIVE, visit MANUALSDOCK

Faqs About iLive IHTB159B Home Theater System