Welcome to ManualsDock! Read Millions of manuals for free.

Get 20% off and boost your website's speed with Hostinger Cloud Hosting!

Honeywell Single-Stage RTH2410 Programmable Thermostat Owner’s Manual

HoneyweHoneywell Single-Stage RTH2410 Programmable Thermostatll Single-Stage RTH2510 Programmable Thermostat-featured

Honeywell-logo

Honeywell Single-Stage RTH2410 Programmable Thermostat

Honeywell Single-Stage RTH2510 Programmable Thermostat

About Honeywell
The corporate headquarters of the American multinational conglomerate Honeywell International Inc. are in Charlotte, North Carolina. Aerospace, building technologies, performance materials and technology, and safety and productivity solutions make up its four main business sectors.

Identify System Type

This thermostat is compatible with the following systems:

  • Gas, oil, or electric furnace
  • Central air conditioner
  • Hot water system with or without pump
  • Millivolt system
  • Central heating and cooling system
  • Heat pump without auxiliary/backup heat
  • Heat pump with auxiliary/backup heat

CAUTION: MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.

CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-
life equipment will help prevent negative consequences for the environment and human health.

FCC statement at: https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx

NOTICE: To avoid possible compressor damage, do not run the air conditioner if the outside temperature drops below 50°F (10°C).

Customer AssistanceHoneywell Single-Stage RTH2510 Programmable Thermostat fig-1


For assistance with this product, please visit honeywellhome.com. Or call Resideo Customer Care toll-free at 1-800-468-1502. To save time, please note your model number and date code before calling. Pull at the bottom to remove the thermostat from the wallplate. Turn the thermostat over to find the model number and date code.

Turn Off Power to the Heating/Cooling System

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-2

Remove Old Thermostat
Remove the old thermostat but leave the wallplate with wires attached.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-3

Label Wires with Tags
Label the wires using the supplied wire labels as you disconnect them.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-4

Separate Wallplate from New Thermostat
Remove the wallplate from the new thermostat and mount it onto the wall.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-5

Mount Wallplate
Mount the new wallplate using the included screws and anchors.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-6

Drill 3/16-in. holes for drywall
Drill 3/32-in. holes for plaster

Connect Wires

Simply match wire labels. If labels do not match the letters on the thermostat, check “Alternate Wiring (Conventional Systems)” on page 6 and connect to the terminal as shown (see notes, below).Honeywell Single-Stage RTH2510 Programmable Thermostat fig-7

Maximum load: 1 A @ 24 Vac, 50/60HZ per output.
We are here to help. Call 1-800-468-1502 for wiring assistance.

Alternate Wiring (Conventional Systems)
If labels do not match the letters on the thermostat, check the chart below and connect to the terminal as shown here (see notes, below).Honeywell Single-Stage RTH2510 Programmable Thermostat fig-8

  1. If wires will be connected to both R and Rc terminals, remove the metal jumper.
  2. Do not use C or X. Wrap the bare end of the wire with electrical tape.
  3. If you have a heat pump without auxiliary/backup heat connect O or, not both.

Alternate Wiring (Heat Pump)
If labels do not match the letters on the thermostat, see page 7.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-9

Alternate wiring (for heat pumps with auxiliary or backup heat only)
If labels do not match the letters on the thermostat, check the chart below and connect to the terminal as shown here (see notes, below).Honeywell Single-Stage RTH2510 Programmable Thermostat fig-10

  1. Leave metal jumper in place, connecting R & Rc terminals.
  2. If your old thermostat had both V and VR wires, stop now and contact a qualified contractor for help.
  3. If your old thermostat had separate O and B wires, wrap the B wire in electrical tape and do not connect.
  4. If your old thermostat had Y1, W1, and W2 wires, stop now and contact a qualified contractor for help.
  5. Do not use C or X wire. Do not use B wire if you already have O wire. Wrap the bare end of the wire with electrical tape.
  6. Do not use L wire. Wrap the bare end of the wire with electrical tape.

If your old thermostat had E and Aux wires (or alternate wires), connect both wires to the Aux terminal.

Install Batteries

Install two AAA alkaline batteries.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-11

Set Fan Operation Switch
Move the switch to the proper setting:Honeywell Single-Stage RTH2510 Programmable Thermostat fig-12

Gas or Oil: For gas or oil heating systems, leave the fan operation switch in this factory-set position (for systems that control the fan in a call for heat).
Electric or Heat Pump: Change the switch to this setting for heat pumps or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call
for heat, if a fan wire is connected to the G terminal.)

Install Thermostat Onto WallplateHoneywell Single-Stage RTH2510 Programmable Thermostat fig-13

Install the thermostat on the wallplate on the wall.

Turn Power Back OnHoneywell Single-Stage RTH2510 Programmable Thermostat fig-14


Turn the power back on to the heating/cooling system.

If Your System Type is…
If your system type is:

  • Single Stage Heat and Cool
  • Heat Only or Cool Only

Congratulations, you’re done!
If your system type is:

  • Heat Pump* with Backup Heat Continue with Advanced Installation to match your thermostat to your system type.
    • Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.

If you are not sure of your system type or if you have other questions, call us toll-free at 1-800-468-1502.
This thermostat works on 24-volt or 750 mV systems. It will NOT work on multi-stage conventional systems.

Advanced Installation

Enter System SetupHoneywell Single-Stage RTH2510 Programmable Thermostat fig-15

To enter the system setup, press and hold both the s and t buttons until the display changes (approximately 5 seconds).

Changing Settings

  1. Press the s or t button to change the setting.
  2. Press the s and t buttons simultaneously for one second to advance to the next function.
  3. Press the RUN button to exit and save settings.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-16

NOTE: If you do not press any button for 60 seconds while you are in the setup menu, the thermostat automatically saves any changes made and exits the menu.

 

Function

Description

 

Press the s or t button to

 

Setting

1 select system type Heating & cooling: Gas, oil or electric heating with central air conditioning or heat pump without auxiliary/ back-up heat.

 

Heat pump with auxiliary/backup heat: Outside

compressor provides both heating and cooling.

5 select your heating system and optimize its operation Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient.

 

Electric furnace: Use this setting if you have any type of electric heating system.

3 Heat pump, hot water or high-efficiency furnace: Use this setting if you have a hot water system or a gas furnace of greater than 90% efficiency.

2 Gas/oil steam or gravity system: Use this setting if

you have a steam or gravity heat system.

13 select Early Start 1 On

 

0 Off

14 select Fahrenheit or Celsius temperature display Fahrenheit temperature display (°F)

 

Celsius temperature display (°C)

15* select Compressor Protection settings 1 On

 

0 Off

20 select clock display 12-hour display

 

24-hour display

21 select Change Filter Timer Off                                                   3  6 months

 

30 days                                        4  9 months

90 days                                        5 1 year

40 restore program schedule to default settings Off

 

On: Program schedule default settings are listed on page 12.

 

Compressor Protection:
This feature forces the compressor to wait approximately 5 minutes before restarting, to prevent equipment damage. During the wait time, the message “Cool On” or “Heat On” is displayed on screen.

About Your New Thermostat

Your new Resideo thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.

  • Backlit display is easy to read
  • Displays ambient (measured) temperature at all times
  • One-touch access to the setpoint temperature
  • Preset program settings
  • Temporary and permanent override of schedule
  • An early start ensures the right temperature at the right time
  • Built-in compressor protection

Thermostat Controls

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-17

Display Screen

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-18

Set the Time and Day

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-19

  1. Press the SET button, then press s or t to set the clock time.
  2. Press the SET button, then press s or t to select the day of the week.
  3. Press RUN to save & exit.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-20

NOTE: If the clock flashes, the thermostat will follow your settings for the Monday “Wake” time period until you reset the time and day.

Program Schedule
You can program four time periods each day, with different settings for weekdays and weekends. We recommend the pre-set settings (shown in the table below), since they can reduce your heating/cooling expenses.

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-21

  • Wake – Set to the time you awaken and the temperature you want during the morning, until you leave for the day.
  • Leave – Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
  • Return – Set to the time you return home and the temperature you want during the evening, until bedtime.
  • Sleep – Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level).

NOTE: Leave and Return periods can be canceled on weekends.

To Adjust Program Schedules (RTH2510)Honeywell Single-Stage RTH2510 Programmable Thermostat fig-22

  1. Press SET until Set Schedule is displayed.
  2. Press s or t to set your weekday Wake time (Mo-Fr), then press SET.
  3. Press s or t to set the temperature for this time period, then press SET.
  4. Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
  5. Press SET to set weekend time periods (Sa & Su), then press RUN to save & exit.

NOTE: Make sure the thermostat is set to the system you want to program (Heat or Cool).

Program Schedule Override (Temporary)

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-24

Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. “Temporary” will appear on the display and the current program period will flash. The new temperature will be maintained only until the next programmed time period begins (see page 12). To cancel the temporary setting at any time, press RUN.

NOTE: Make sure the thermostat is set to the system you want to control (heat or cool).

Program Schedule Override (Permanent)Honeywell Single-Stage RTH2510 Programmable Thermostat fig-25

Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods.
The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed.
Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press RUN to cancel “Hold” and resume the program schedule.
NOTE: Make sure the thermostat is set to the system you want to control (heat or cool).

Built-In Compressor Protection

This feature helps prevent damage to the compressor in your air conditioning or heat pump system.Honeywell Single-Stage RTH2510 Programmable Thermostat fig-26

Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait 5 minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.

Early StartHoneywell Single-Stage RTH2510 Programmable Thermostat fig-27


This feature allows the heating or cooling to turn on before the program start time, so the temperature is reached at the time you set. For example: Set the Wake time to 6 am and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6. The next time period is displayed when the system is activated before a scheduled time period.

Change FilterHoneywell Single-Stage RTH2510 Programmable Thermostat fig-28


If the filter reminder is turned on during installation, the words Change Filter will flash on the screen when the filter needs to be replaced. After you replace the air filter, press and hold the RUN button for 3 seconds to reset the alert.

Battery Replacement

Honeywell Single-Stage RTH2510 Programmable Thermostat fig-29

Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo Batt appears for 60 days before the batteries are depleted. Replace batteries once a year, or when you will be away for more than a month.
Most settings are stored in non-volatile (permanent) memory. Only the clock and the day must be set after you replace the batteries. Honeywell Single-Stage RTH2510 Programmable Thermostat fig-30

Set the System switch to Off before removing the batteries. Otherwise, the heating/cooling system could remain activated even when the batteries are removed.

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.

The display is blank:
Make sure fresh AAA alkaline batteries are correctly installed.

The heating or cooling system does not respond

  • Set the system switch to Heat. Make sure the temperature is set higher than the Inside temperature.
  • Set the system switch to Cool. Make sure the temperature is set lower than the Inside temperature.
  • Wait 5 minutes for the system to respond.

Temperature settings do not change

Make sure heating and cooling temperatures are set to acceptable ranges:

  • Heat: 40° to 90°F (4.5° to 32°C).
  • Cool: 50° to 99°F (10° to 37°C).

“Cool On” or “Heat On” is flashing
The compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.

“Heat On” is not displayed
Set the System switch to Heat, and set the temperature level above the current room temperature.

“Cool On” is not displayed
Set the System switch to Cool, and set the temperature level below the current room temperature.

For assistance with this product, please visit honeywellhome.com or call Resideo Customer Care toll-free at 1-800-468-1502.

1-Year Limited Warranty

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of one (1) year from the date of first purchase by the original purchaser. If at any time during the warranty period, the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Reside o’s option).
If the product is defective,

  1.  return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
  2. call Resideo Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage that occurred while the product was in the possession of a consumer.

Reside o’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422, or call 1-800-468-1502.

Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
33-00110EF—05 M.S. Rev. 10-21 | Printed in United States

www.resideo.com

FAQs Honeywell Single-Stage RTH2410 Programmable Thermostat Owner’s Manual

How long does a Honeywell thermostat last?

The normal lifespan of a thermostat for upkeep, repair, or replacement is variable (unlike air conditioners that need a tune-up every year). However, in general, you can count on your thermostat to endure for at least ten years. Thermostats may start acting up after ten years.

How much time does a Honeywell thermostat take to reset?

A Honeywell thermostat reset Negative to positive and positive to negative battery insertion is incorrect. Place them back in the proper order when ten seconds have passed. You’ll get a factory reset for your thermostat. Don’t forget to set your thermostat to your regular routine.

How can I program my Honeywell thermostat such that it stays in one setting?

Press up or down until the appropriate temperature is displayed to permanently ignore the timetable. Press the Hold button to keep the new temperature for an infinite period of time. On the screen, the word “Hold” will display. If you want to stop either override or start the schedule again, click the Run button.

What happens if the thermostat is left shut?

The circulation of the coolant is obstructed if the thermostat gets stuck in the closed position; as a result, the coolant cannot reach the radiator to cool it, which leads to engine overheating.

Should I change the thermostat’s batteries?

Batteries for thermostats There is a low battery indicator light on Honeywell thermostats. You’ll have roughly 60 days to change the batteries after this light turns on.

Why does a thermostat malfunction?

Contaminated fluid or an outdated thermostat with frayed springs can both result in thermostat failure. When incompatible coolants are mixed, the old coolant is not changed as advised, or particles from gaskets or other places break off contamination results.

How frequently should batteries be changed in a thermostat?

around once each year When necessary, changing the batteries in your thermostat is a quick and straightforward task for home maintenance. Batteries for thermostats often need to be changed once a year. You shouldn’t have any issues keeping control of your thermostat if you regularly change them.

What’s the difference between the Honeywell Thermostat’s fan on and the fan auto?

AUTO indicates that the fan only activates when air is being heated or cooled by your system. The entire system turns off until the following cycle once the thermostat reaches the desired temperature. When your HVAC system is not heating or cooling air, ON signifies that the fan is continually on and blowing air.

What is the mechanism of a Honeywell Thermostat?

When the air temperature drops below the thermostat setting, the heating turns on, and when the set temperature is achieved, it turns off. This is how it works. The temperature in the room won’t increase any faster if the thermostat is turned up.

How do you maintain the same temperature in every room?

Putting up a Zoned System With zoned HVAC systems, you can use separate thermostats to independently regulate the temperatures of various rooms. These systems assist maintain a uniform temperature by adjusting dampers that are installed in the ducting. Additionally, they let you quickly cool select areas while keeping empty rooms warmer.

How is a thermostat tested?

common thermostats: enlist the help of a friend or relative, Place one person near the furnace and the other near the thermostat. Turn the thermostat gradually to the heat setting to raise the temperature. The furnace and thermostat should both make noise.

Pdf – Honeywell Single-Stage RTH2410 Programmable Thermostat Owner’s Manual

For More Manuals Visit: ManualsDock

Leave a Comment