Starfrit PRO Fry Cutter and Cuber
Introduction
FRY CUTTER ASSEMBLY
- Lift the handle so that it stands vertically.
- Insert the pusher plate into the end of the pusher plate holder.
Lock it by turning it counterclockwise.
Insert the square blade cartridge (the one with the grid pattern) into its compartment until it stops. WARNING sharp blades: hold the blade cartridge by the plastic frame.
Toggle the lever to secure the unit. WARNING: Always place the unit on a clean, flat, non-textured surface.
CUBER ASSEMBLY
- Do the fry cutter assembly.
- Insert the horizontal blade cartridge (the one with the straight pattern) into the pusher housing until it stops. WARNING sharp blades: hold the blade cartridge by the plastic frame.
Assemble the housing pusher onto the fry cutter and secure it by sliding it forward in the right direction.
Insert the pusher into the pusher housing.
Toggle the lever to secure the unit. WARNING: always make sure to place the unit on a clean, flat, and non-textured surface.
HOW TO USE – FRY CUTTER
- Lift the handle so that it stands vertically.
Insert the food into the cavity (between the pusher plate and the square blades).WARNING: Always ensure the food does not exceed the maximum height and width of the square blades. It might be necessary to trim the potato.
Lower the handle.
Repeat steps 1 to 3 as many times as necessary.
HOW TO USE – CUBER
- Lift the handle so that it stands vertically.
Remove the pusher and insert the food inside the cavity. WARNING: Always ensure the food does not exceed the maximum height, width, and height of the cavity. It might be necessary to trim the potato.
Place hands on the pusher and push until the food is completely processed.
Place one hand on the handle and push it down completely.
Repeat steps 1 to 4 as many times as necessary.
CLEANING
Disassemble all parts and wash them In warm soapy water.
TIP
If you have to trim your potato make sure that the trimmed part is NOT facing the blade otherwise it will be harder to cut.
For more Manuals by STARFRIT, visit MANUALSDOCK
FAQS About Starfrit PRO Fry Cutter and Cuber
What does the Starfrit PRO Fry Cutter and Cuber do?
The Starfrit PRO Fry Cutter and Cuber is a kitchen tool designed to effortlessly cut potatoes into fries and cubes.
What types of potatoes can I use with the Fry Cutter and Cuber?
You can use various types of potatoes, including russet, Yukon Gold, and sweet potatoes, with the Fry Cutter and Cuber.
What are the dimensions of the fries and cubes produced by the Fry Cutter and Cuber?
The Fry Cutter and Cuber typically produce fries and cubes with dimensions of approximately 1/2 inch by 1/2 inch.
Is the Fry Cutter and Cuber easy to clean?
Yes, the Fry Cutter and Cuber is designed for easy cleaning. Most parts are detachable and dishwasher-safe.
Can the Fry Cutter and Cuber be used for other vegetables besides potatoes?
While primarily designed for potatoes, the Fry Cutter and Cuber can also be used for other firm vegetables like carrots, zucchini, and cucumbers.
Does the Fry Cutter and Cuber require assembly?
Yes, some assembly is required upon initial setup, but it’s straightforward and doesn’t require any special tools.
What material is the Fry Cutter and Cuber made of?
The Fry Cutter and Cuber is typically made of durable plastic and stainless steel blades.
Is the Fry Cutter and Cuber safe to use?
Yes, the Fry Cutter and Cuber is equipped with safety features to ensure safe operation. However, it’s essential to follow the instructions provided.
Can the Fry Cutter and Cuber be used commercially?
While primarily designed for home use, some models of the Fry Cutter and Cuber may be suitable for light commercial use, but it’s best to check the manufacturer’s guidelines.
How long does it take to cut a potato using the Fry Cutter and Cuber?
The time it takes to cut a potato depends on factors like the size and firmness of the potato, but typically, it’s a quick process, taking only a few seconds per potato.