Mattress Firm 300
About Mattress Firm
Mattress Firm is a U.S.-based specialty retailer of mattresses and bedding accessories. The company was founded in 1986 and is headquartered in Houston, Texas. Mattress Firm operates over 2,500 stores across the United States, making it one of the largest mattress retailers in the country. The company offers a wide range of mattresses from leading brands such as Serta, Sealy, Simmons, and Tempur-Pedic, as well as its own private-label brands. In addition to mattresses, Mattress Firm also sells bedding accessories such as pillows, sheets, and mattress protectors.
Adjustable Base setup guide
STEP 1: Remove the top of the shipping carton. Verify contents; inspect for damage.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE.
- x6 – Pin-adjustable Legs
- x1 – Remote Control (varies according to base type)
- x4 – 3-Inch Carriage Bolts and Nuts
- x2 – T-Spacers
- x1 – Mattress Retainer
- x2 – Center Support Brackets
- x3 – AAA Batteries
- x1 – WRENCH
STEP 2: Cut the zip-tie from the electrical power supply. Cut (2) zip-ties and remove the mattress retainer (set aside) (FIGURE 1).
CAUTION: BE CAREFUL USING SHARP INSTRUMENTS. INJURY IS POSSIBLE IF TOOLS ARE NOT USED PROPERLY.
WARNING: PINCH POINT WARNING! KEEP HANDS AND FINGERS CLEAR WHEN SLIDING BASES TOGETHER.
STEP 3
- Carefully lift the base head section out of the shipping carton and place it on a clean surface (FIGURE 2).
- Remove the divider from the shipping carton.
- Carefully lift the base foot section out of the shipping carton and place adjacent to the head section (FIGURE 2).
- Slide head and foot sections together making sure to align mounting holes (center of base sections) (FIGURE 2).
STEP 4
- Place a T-Spacer in between the mounting points (each side of the base). Line up the holes in the T-Spacers with the holes in the mounting points (FIGURE 3).
- Place a center support bracket over the mounting points on each side of the base. Insert carriage bolts through the square holes in the center support bracket. Install nuts on carriage bolts (FIGURE 3). HAND TIGHTENS.
- After all, the hardware is installed, tighten all nuts using the provided wrench.
STEP 5
- Route FOOT MOTOR CABLE underneath the base frame and connect it to HEAD MOTOR CABLE (FIGURE 4).
- 600 MODEL ONLY – Route FOOT MASSAGE MOTOR CABLE underneath the base frame and plug into the control box (FIGURE 4).
- Extend the electrical power cord out the head end of the base.
WARNING: POWER CORDS MUST NOT INTERFERE WITH ANY ADJUSTABLE BASE MECHANISMS.
STEP 6
- Screw (4) legs into the threaded inserts at the corners of the base frame (FIGURE 5).
- Screw (2) legs into the threaded inserts of the center support brackets (FIGURE 5).
- Push the pin in to adjust leg height (6 inches to 10 inches).
- Note: When adjusting legs, make sure the base sets level on the floor.
STEP 7: Rotate the base over onto its legs. Remove the remaining packaging.
WARNING: DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE.
STEP 8
- Install (3) batteries in the remote control.
- Plug the power cord into a power outlet. Note: An electrical surge protection device is recommended (not included).
- Operate remote control to test base functions (FIGURE 6) (see separate Syncing Guide).
STEP 9
- Lower base to a flat position.
STEP 10
- Install the mattress retainer at the foot end of the base.
- Place one end of the mattress retainer into the outside hole of the left insert and place the other end into the outside hole of the right insert (FIGURE 7).
STEP 11: Place the mattress on the base to complete assembly.
Note: If the adjustable base will not operate, refer to the Troubleshooting section of the owner’s manual. To download a copy of the owner’s manual, visit https://lpadjustablebeds.com/om/mattressfirm or call Mattress Firm at 844-628-8376.
To register your adjustable base, please go to https://lpadjustablebeds.com/register or call Mattress Firm at 844-628-8376.
FAQs About Mattress Firm 300 Setup
How can I reset the adjustable base on my mattress firm 300?
To reset the electronic components, unplug the base for five minutes. Attempt using a different electrical outlet for the adjustable base or test the outlet with a functional appliance (a grounded, electrical surge protector is recommended.)
Why won’t my adjustable mattress firm base work?
Verify the wiring connections are solid and that no cords or bedding are impeding the movement of the bed foundation by looking under the base. Make sure the control box’s green LED light is on by checking. Check to see if the input and power cords are correctly connected if there is no light.
Why won’t my adjustable bed remain raised?
You can take a few actions to resolve this issue. Make sure the bed’s tracks are clear of debris and clean by checking them first. The bed may not move smoothly or stick if the tracks are unclean. You can also experiment with changing the springs’ tension.
What parts of an adjustable bed are there?
The sleeping surface, which the mattress will lay on, is the second of two parts that make up an adjustable foundation. The joints are located in the second section on the opposite side. The joints enable the base to move freely on the mattress, allowing for a variety of sleeping positions.
What parts of an adjustable bed are there?
The sleeping surface, which the mattress will lay on, is the second of two parts that make up an adjustable foundation. The joints are located in the second section on the opposite side. The joints enable the base to move freely on the mattress, allowing for a variety of sleeping positions.
How long does a mattress take to adjust?
Although 30 days is the typical recommendation, the length of time may vary based on the sort of mattress that was bought. Innerspring types, for instance, are renowned for adjusting more quickly although they can potentially take up to 4 weeks.
What causes the shifting of a mattress?
The lack of friction between the mattress and the bed frame is a common cause of mattress sliding. This can occur if the rails above the slats are missing, if the frame is the improper size, or if the mattress is old.
While not in use, should adjustable beds be flat?
Although adjustable beds are made to be elevated while in use, leaving them upright is not a good idea. When not in use, try to lower your adjustable bed so that the mattress and frame may lay flat. If you store your adjustable bed flat whenever you can, you should get more usage out of it.
Why is the buzzer on my adjustable bed?
The remote control can simply not have enough power due to a set of failing batteries. Alternatively, the problem can be that the wall outlet isn’t functioning properly or that the power cord for the adjustable bed isn’t entirely plugged in.
Exists a break-in period for new mattresses?
It is typically advised to give your mattress at least a week to get used to your body. During this time, sleep on your new mattress every night to help it loosen and stretch as needed. A week-long break-in period is advised unless your mattress is very uncomfortable for sleep.
Why won’t my remote connect?
Verify that none of the remote’s buttons are stuck or jammed. The battery connectors for the remote control could be unclean. Place the batteries back into the remote control after removing them and use a cotton bud or soft cloth to wipe the remote control terminals with a tiny solution of alcohol.
How do I change the settings on my remote?
Most remote controls feature reset options unique to each model that require pressing and holding a number of buttons. It might only require holding down the power and menu buttons for a little period of time, but this will depend on the brand and kind of remote control you have.
For more manuals by Mattress Firm, visit ManualsDock