JIMMY H10 Flex Cordless Stick Vacuum Cleaner Instruction Manual

JIMMY H10 Flex Cordless Stick Vacuum Cleaner

Parts Name

1. Battery pack release button
2. On/off switch
3. Mode button
4. LED screen
5. Dust cup bottom release button
6. Metal tube release button
7. Floorhead release button
8. Metal tube bending release button
9. Storage holder
10. Charger
11. Connector
12. Upholstery tool
13. Flexible crevice tool
14. Soft brush
15. Electric mattress head
16. Carpet brush roll

Storage holder parts name

1. Machine holder
2. Screw ST4-32 *2
3. Accessory holder right
4. Electric mattress head holder
5. Screw ST3-12 *2
6. Expansion pipe
7. Accessory holder left
8. Screw ST4-16 *2

Charging holder assembly

1. Assemble the left and right accessory holders to the charging holder, then fasten the accessory holders with a screw.
2. Put the vacuum cleaner in the holder, and lean the vacuum cleaner against the wall, place the holder in a position where the vacuum cleaner floorhead just touches the ground, proposed height of 90cm. Take off the handheld vacuum cleaner, place the expansion pipe on the wall and place the holder to the expansion pipe position, then lock in the screw.
3. After assembly is completed, put the vacuum in the charger holder to charge or store. Attention: Do not fix the holder to the bathroom or another humid wall.

Packing List

Machine assembly

Assemble and disassemble the electric floor head with a flexible metal tube

Hold the floor head with the left hand, use the right hand to insert the metal tube vertically into the floor head, align it with the conductive needle, and press the tube until a “click” sound is heard.

Attention
Keep the handle and floor head in the same direction, conductive needle shall align with the socket. When packing, storing, or cleaning, if the electric floor head needs to be removed, press the brush release button and pull the metal tube in the direction shown in the picture to take out the floor head.

Assemble battery pack with handheld vacuum
Hold the battery pack, align it with the guiding slot on the handheld vacuum body, and slide in the battery pack in the arrow direction in the picture. Then pull the battery pack after installation to make sure it does not get loose.

Attention
when the vacuum cleaner is long idled, please remove the battery, pack the machine, and store it in a cool and dry place, avoiding direct sunlight or a humid environment.

Assemble floor head and metal tube assembly with handheld vacuum
First, assemble the floor head and metal tube according to the method of assembling the electric floor head with the metal tube. Then, as shown by the arrow, align the conductive needle of the metal tube with the coupler of the handheld vacuum suction nozzle, and push the metal tube upward until a“click” sound is heard.

Assembly of accessories
For the convenience of use, this product is specially equipped with some accessories for the hand-held part of the vacuum cleaner. When you use the handheld vacuum cleaner alone, you can directly connect the accessories according to your needs.

Accessories Connection List

Use of vacuum cleaner

Charging
Attention

1. When using the product for the first time, the battery power is not full. Need to charge the vacuum before using it.
2. If the power cord is damaged, to avoid danger, it must be replaced by a professional person of the manufacturer, repairing agent, or similar department.

The product can be charged in two ways

1. Charge the battery pack separately: Plug one end of the charger into the battery pack connector and another end of the charger into a power socket to charge the battery directly. In this way when undercharging the indicator on the side of the battery pack is red and turns green when charging is completed.
2. Charge the battery on the machine: lug one end of the charger to the battery pack connector and another end of the charger to a power socket to charge the battery when the battery pack is assembled in the vacuum cleaner. The machine’s LED screen will show the battery power percentage. When charging is completed it will show 100% as the pictures show.

Attention

1. When battery power is below ≤20% If the machine is working in Max mode in this status, it will change to Eco mode automatically. When battery power runs off, the machine will turn off.
2. If the vacuum cleaner is long idled, charge the battery every three months to avoid battery failure.

Use of handheld vacuum and LED screen contents

Take the vacuum cleaner off the storage holder, and press the on/off button to start or stop the vacuum cleaner. The mode button can adjust the working mode. When the machine is turned on, it works in Auto mode, press the mode button to switch to the sequence of Turbo- Max – Eco-Auto mode. The Middle of the LED screen displays the product run time left in current mode. When the mode is changed, the left run time will also change accordingly.

When the product works in Max mode and battery power drops below 20%, to extend product run time, the product will automatically switch from Max to Eco mode. After the battery is charged to higher than 20% power, the product can work in Max mode. When the product is working in Auto mode, it will adjust working power based on the dust content and the floor type it detects, to achieve higher cleaning efficiency.

Under Auto mode, the LED screen displays Auto regardless of how high the working power is. The product is equipped with a dust-content sensor. On the LED screen bottom, there is a light strip to display the dust content. As dust content decreases from high to low, the red color decreases, and the blue color increases. When the strip is completely blue, the cleaning surface is clean. The Cleanness of the cleaning surface can be visually displayed through the LED screen.

Use of flexible metal tube 
The flexible metal tube has two modes: vertical and bending. The vertical mode is equivalent to the normal metal tube. The bending mode can be used for cleaning under the sofa, table bed, etc. Press the release button when the bending mode is needed, and the metal tube can achieve a 0-90°bending angle.

Use of electric floor head
The electric floor head is suitable for cleaning all kinds of hard floors, tiles, carpets, etc. The product comes with an extra carpet brush roll that can be replaced to the floor head to deep clean the carpet.

Attention
During the operation of the electric floor head, if there is a large volume of foreign matter inhaled or too much fiber wound, or even a child in the play of the machine mistakenly puts his hand into the nozzle, resulting in the brush roll abnormal stop, the electric floor head will stop working, to protect personal safety and brush motor.

Use of accessories
Flexible crevice tool: The crevice tool can be bent at an angle with LED light in the head. Suitable for cleaning crevices, doors, window corners, and other narrow gaps as well as hard-to-reach areas.

Upholstery tool
suitable for cleaning closet, windowsill, sofa, and table surface.

Soft brush
suitable for cleaning easy-to-scratch furniture like bookshelves, handicrafts, etc.

Electric mattress head
Suitable for sofa and bed mattresses. The brush roll beats out and then cleans the dust mites and allergens from the deep sofa or bed.

Connector
Can be connected to other tools and bent to different angles to clean dust on top of high cabinets or dust on the roof.

Cleaning and Replacing Parts

Attention

1. HEPA filters are available for sale from local vacuum cleaner distributors.
2. It is recommended to clean the dust cup after each use; When the dust cup is full or the HEPA filter is clogged, it needs to be cleaned and replaced if necessary.
3. Electric floor head brush roll might be entangled with hair after a long time of use. It needs to be cleaned in time to keep the vacuum working more efficiently.

Clean dust cups and filters

1. Press down the dust cup bottom cover to open the dust cup bottom cover. Fig 1
2. Dump dust into the trash can. Fig 2
3. Hold the dust cup lid and rotate it anti-clockwise, remove the cyclone assembly from the dust cup for cleaning. Fig 3
4. Rotate the cyclone anti-clockwise, and disassemble the cyclone to clean. Fig 4
5. Hold the HEPA lid and rotate it anti-clockwise, remove the HEPA assembly from the top cover, and then rotate the HEPA lid to remove HPEA from the lid for cleaning. Fig 5
6. If HEPA needs washing, hold the HEPA and rotate it clockwise, remove it from the HEPA lid for washing. HEPA needs to be completely dry before reuse. Fig 6
7.  After cleaning, assemble the parts back in the opposite sequence of disassembly

Clean brush roll

1. Move the brush roll release button along the arrow direction and remove the side cover.
2. Remove one end of the brush roll and take it out from the nozzle for cleaning.
3. After cleaning or replacing the brush roll, assemble it back in the opposite sequence of disassembly

Vacuum cleaner storage

Battery pack disassembly
Press the battery release button, pull the battery pack out backward and place the battery in a plastic bag, then store it in a dry place.

Product storage
When the vacuum is long idled, remove the battery, pack the machine, and store it in a cool and dry place, do not put it in direct sunlight or a humid environment.

Safety Notes

• This vacuum cleaner is designed for home use. Do not use it for commercial or other purposes.
• Please read this instruction manual carefully before use, properly save, and store it for future use.
• Do not put the vacuum close to a fire or other high-temperature facility.
• Do not use or store the machine under extremely bad conditions, for example, extreme temperatures. It is recommended to use it indoors between the temperature of 5 °C to 40 °C.
• Store the machine in a dry place and avoid direct sunlight.
• Fully charge the battery before first use or after long storage.
• Before using the vacuum, make sure the brush roll is assembled, otherwise, it may lead to motor fan blockage, causing motor burnout.
• Please do not use the vacuum to pick up detergent, oil, glass slag, needles, cigarette ash, wet dust, water, matches, etc.
• Please do not use the vacuum to pick up tiny particles such as cement, gypsum powder, wall powder, or large objects such as paper balls, otherwise, it will cause malfunctions such as blockage and motor burnout.
• Avoid blockage to air inlet or brush roll, it may cause motor failure.
• Do not put your hand or foot into the floorhead inlet to avoid body hurt.
• Do not pour or splash water or other liquids into the machine to avoid short circuit to burn out the machine.
• If the brush roll is not working, please check whether the brush roll is entangled with hair or other long fiber, and clean it in time.
• When storing the machine for a long time, ensure that the battery is fully charged before storage and charge the machine at least every three months.
• Unplug the charger to clean or repair the machine. Hold the charger when plugging or unplugging it, and do not pull the charging cord.
• Use a dry cloth to clean the machine. Liquids like gasoline, alcohol, and lacquer thinner will cause cracks or color fading and cannot be used.
• If the machine is not working after fully charged, it must be checked and repaired in our designated office, please do not dismantle the machine on your own.
• The discarded machine contains batteries. They should be recycled safely. Do not discard them randomly.
• If there is damage to the power cord, to avoid danger, it should be replaced or repaired by the manufacturer、repairing agency, or a professional person.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• The appliance is only to be used with the power supply unit provided.

Trouble Shooting

Please check the following issues before sending them to the designated repair agent.

Warning reminding

1. When the air path or HEPA filter is clogged or the dust cup is full, there will HEPA cleaning reminder Icon on the LED screen. If the machine is working in Max mode, it will change to Eco mode automatically until the blockage is cleaned.
2. When the brush roll is tangled by foreign objects, continuing to use the product will activate brush roll blockage protection. The LED screen will display F0 and the product will stop working until the brush roll is cleaned.
3. If the dust level light on the screen is always red, the dust sensor might be covered by dust, please clean the dust on the dust sensor which is located in the suction inlet of the handheld vacuum cleaner.
4. When there is an electric component defect,  that needs a professional after-service person for instruction or repair, the Screen will display the defect warning with an error code of F0 to F9. Please contact after service of the local agent and provide the error code.

The defect of F0 to F9 is as follows

Attention: If any other failures occur, which need professional tools, to avoid danger, the machine must be repaired or replaced by the manufacturer, other maintenance offices, or professionals from similar offices.

Technical specification

Circuit Diagram

Warranty Information

This product enjoys two years warranty from the date of purchase. Excluded from the guarantee are normal wear, commercial use, alterations to the appliance as purchased, cleaning activities, consequences of improper use or damage by the purchaser or a third person, and damage that can be attributed to external circumstances.

For more Manuals by JIMMY, visit MANUALSDOCK

FAQS About JIMMY H10 Flex Cordless Stick Vacuum Cleaner