EverStart MAXX PPS1CWE 1000 Amp Jump Starter Instructions Manual

EverStart MAXX PPS1CWE 1000 Amp Jump Starter

About This Brand

Johnson Controls is the manufacturer of EverStart batteries. These are high-quality, long-lasting, and low-maintenance. The EverStart series offers both AGM and lead-acid batteries. The two most widely used AGM battery models are EverStart Plus and EverStart Maxx.

Visit: EverStart JUS750CE Jumper Starter or EverStart SL097 Jump Starter

FEATURES

1. Carry Handle
2. Wireless Charging Pad
3. LED Area Light
4. LCD Screen
5. LED Light Power Button
6. Decrease Compressor Pressure Control Button (–)
7. Boost Cables
8. Alternator Check Button
9. Compressor Power Button
10. Wireless Charging Button
11. USB Power Button
12. Increase Compressor Pressure Control Button (+)
13. USB Ports (with USB Power/Fault Indicators)
14. AC Charging Port
15. Air Hose and Sure Fit® Nozzle
16. Boost Cables Connector
17. Clamp Connection Slot
18. Air Hose and Sure Fit® Nozzle in Hose Storage Groove
19. Nozzle Adapter
20. AC Charging Adapter

LCD DISPLAY DETAIL

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. The manufacturer strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

READ ALL INSTRUCTIONS Manual

WARNING:
Read and understand this instruction manual before using this unit. Failure to follow all instructions manual listed below may result in electric shock, fire, and/or serious injury.

IMPORTANT SAFETY INSTRUCTIONS Manual

GENERAL SAFETY WARNINGS AND INSTRUCTIONS Manual

replica vintage military watches best replica watches tag heuer Jessie james replica pocket watch Swiss Panerai replica watches Civil War pocket watch replica replica watches Maurice Lacroix

• This unit was designed for household use only.
  WARNING – To reduce the risk of fire, electric shock, burst hazard, or injury to persons or property:
• Avoid dangerous environments. Don’t use appliances in damp locations. Don’t use appliances in the rain.
• Keep children away. All visitors should be kept at a distance from the work area.
• Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear a protective hair covering to contain long hair.
• Store idle appliances indoors. When not in use, appliances should be stored indoors in a dry and high or locked-up place – out of reach of children.
• Don’t abuse the cord. Never carry the appliance by a cord or yank it to disconnect it from the receptacle. Keep cord from heat, oil, and sharp edges.
• Disconnect appliances. Disconnect the appliance from the power supply when not in use, before servicing, and when changing accessories.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
• Use of accessories and attachments. The use of any accessory or attachment not recommended for use with this appliance could be hazardous. Refer to the accessory section of this manual for further details.
• Stay alert. Use common sense. Do not operate this equipment when you are tired or impaired.
• Check for damaged parts. Any part that is damaged should be replaced by the manufacturer before further use. Do not use the tool if the switch does not turn it on and off. Contact the manufacturer at 1-877-571-2391 for more information.
• Do not operate this appliance near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.
• Never submerge this unit in water; do not expose it to rain, or snow or use it when wet.
• To reduce the risk of electric shock, disconnect the unit from any power source before attempting maintenance or cleaning. Turning off controls without disconnecting will not reduce this risk.
• This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor.

SPECIFIC SAFETY INSTRUCTIONS MANUAL FOR CHARGING THIS UNIT

• IMPORTANT: This unit is delivered in a partially charged state. Charge the unit with the AC charging adapter for a full 20 hours before using it for the first time.
• To recharge this unit, use only the supplied AC charger.
• All power switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.

Extension cords

WARNING:
The use of improper extension cords could result in a risk of fire and electric shock. When using an extension cord, make sure that the pins of the extension cord are the same number, size, and shape as those in the charger; and be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

When an extension cord is used, make sure that:

• the pins of the extension cord are the same number, size, and shape as those in the charger,
• the extension cord is properly wired and in good electrical condition,
• the wire size is large enough for the AC rating of the charger.

CAUTION – To reduce the risk of injury or property damage: Pull the extension cord by the plug rather than the cord when disconnecting from the 120-volt AC charging port or the AC outlet.

Visit: EverStart SL097 Jump Starter

SPECIFIC SAFETY INSTRUCTIONS MANUAL FOR WIRELESS CHARGING

CAUTION – To reduce the risk of property damage:

• Do not attempt to use the Jump-Starter or Compressor when using the Wireless Charging function.
• Place the appliance in the center of the Wireless Charging Pad.

SPECIFIC SAFETY INSTRUCTIONS MANUAL FOR JUMP STARTERS

WARNING – Burst hazard:
Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage property. Use the unit for charging/boosting a lead-acid battery only. It is not intended to supply power to a low-voltage electrical system other than in a starter-motor application.

• Use of an attachment not supplied, recommended, or sold by manufacturer specifically for use with this unit may result in a risk of electrical shock and injury to persons.
• WARNING – Risk of explosive gases:
  • Working in the vicinity of EverStart MAXX PPS1CWE 1000 Amp Jump Starter lead acid battery is dangerous. EverStart MAXX PPS1CWE 1000 Amp Jump Starter Batteries generate explosive gases during normal battery operation. For this reason, it is of the utmost importance that each time before using the jump-starter you read this manual and follow the instructions manual exactly.
  • To reduce the risk of battery explosion, follow these instructions manual and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary markings on these products and on the engine.
• CAUTION – To reduce the risk of injury or property damage:
  • NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.
• Vehicles that have on-board computerized systems may be damaged if the vehicle battery is jump-started. Before jump-starting, read the vehicle’s owner’s manual to confirm that external-starting assistance is suitable.
• When working with EverStart MAXX PPS1CWE 1000 Amp Jump Starter lead acid batteries, always make sure immediate assistance is available in case of an accident or emergency.
• Never smoke or allow a spark or flame in the vicinity of the vehicle battery, engine, or power station.
• Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.
• Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead acid battery. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin, causing a severe burn.
• Do not wear vinyl clothing when jump-starting a vehicle. Friction can cause dangerous static electrical sparks.
• Be extra careful to avoid dropping a metal tool onto the battery. It might spark or short-circuit the battery or another electrical part and could cause an explosion.
• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangerous sparks, power arcing, and/or explosion.
• When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing, and body parts away from moving vehicle parts.
• Never allow red and black clamps to touch each other or another common metal conductor — this could cause damage to the unit and/or create a sparking/explosion hazard.
• If the clamps are connected incorrectly about polarity, the backlit LCD screen will display the Battery Status Icon, Battery Voltage Indicator, and Clamp Icons. The Alarm Icon, the “+” and ”–” signs, and the Reverse Polarity Icons will flash and the unit will sound a continuous alarm until the clamps are disconnected. Disconnect the clamps and reconnect to the battery with the correct polarity.
• Always disconnect the negative (black) jumper cable first, followed by the positive (red) jumper cable, except for positive grounded systems.
• Do not expose the battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Place this unit as far away from the battery as cables permit.
• Never allow battery acid to come in contact with this unit.
• Do not operate this unit in a closed area or restrict ventilation in any way.
• This system is designed to be used only on vehicles with a 12-volt DC battery system. Do not connect to a 6-volt or 24-volt battery system.
• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not have a battery installed.
• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.
• Do not use this jump starter on a watercraft. It is not qualified for marine applications. • Although this unit contains a non-spillable battery, it is recommended that the unit be kept upright during storage, use, and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat, and/or moisture.

SPECIFIC SAFETY INSTRUCTIONS MANUAL FOR THE USB POWER PORTS

• Do not insert foreign objects into the USB Power Ports.
• Do not attach USB hubs or more than one personal electronic device to each USB Power Port.
• Do not use this unit to operate appliances that require more than 3.1 amps in total to operate from the USB power ports.

SPECIFIC SAFETY INSTRUCTIONS MANUAL FOR COMPRESSORS

WARNING – BURST HAZARD:

• Bursting articles can cause serious injury.
• Carefully follow the instructions manual on articles to be inflated.
• Never exceed the recommended pressure listed in the instructions manual on articles to be inflated. If no pressure is given, contact the article manufacturer before inflating.
• Monitor the pressure at all times on the pressure gauge.

CAUTION – To reduce the risk of injury or property damage:

• Never leave the compressor unattended while in use.
• Do not operate the compressor continuously for longer than approximately 10 minutes, depending on ambient temperatures, as it may overheat. This could damage the compressor.

FIRST AID
When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.
Always have protective eyewear when using this product. Contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid. Have plenty of fresh water and soap nearby in case battery acid contacts the skin.

WARNING – Battery fluid is a diluted Sulphuric acid and may cause personal injury or damage to property. In case of skin or eye contact, follow the instructions below.

• Skin: If battery acid comes in contact with the skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.
• Eyes: If battery acid comes in contact with your eyes, flush your eyes immediately, for a minimum of 15 minutes, and seek immediate medical attention.
• LCD liquid crystal display: If liquid crystal comes in contact with your skin: Wash the area off completely with plenty of water. Remove contaminated clothing. If liquid crystal gets into your eye: Flush the affected eye with clean water and then seek medical attention. If liquid crystal is swallowed: Flush your mouth thoroughly with water. Drink large quantities of water and induce vomiting. Then seek medical attention.

SAVE THESE INSTRUCTIONS MANUAL

WARNING – To reduce the risk of injury: Follow these instructions manual and those published by the battery manufacturer and manufacturer of any equipment you intend to use with this unit. Review cautionary markings on these products and the engine.

OVERVIEW

Common Actions and Unit Responses
The following actions turn the unit on and activate the LCD screen:

Note: The unit will automatically power off once ALL the functions are turned off.

VIEWING BATTERY STATUS

The Battery Status Icon and Battery Voltage Indicator indicate the battery charge level as follows.

• If the battery charge level is at full capacity, four solid bars will display.
• If the battery is partially charged, two or three solid bars will be displayed.
• If the battery is nearly empty, one solid bar will display. The unit should be charged at this time.
• If the battery is empty, four blank bars will display. The unit MUST be charged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period before automatic shutdown. The unit will not operate until the battery is recharged.

CHARGING/RECHARGING

Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost through self-discharge. When the unit is not in frequent use, the manufacturer recommends the battery should be recharged at least every 30 days and after each use.

IMPORTANT CHARGING NOTES 

1. This unit is delivered in a partially charged state – you must fully charge it before using it for the first time. The initial AC charge should be for 20 hours or until the Battery Status Icon shows 4 solid bars.
2. Recharging the battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life.
3. Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.

Visit: EverStart Maxx EL224

CAUTION – Risk of property damage: Failure to keep the battery charged will cause permanent damage and result in poor jump-starting performance.

IMPORTANT:
If you know the unit is discharged, but the battery icon displays four solid bars as if the unit is fully charged when connected to a charging power source, this may be due to the internal battery having high impedance. The manufacturer suggests leaving the unit charging for 20 hours using the supplied AC charger before use.

PROCEDURE

1. 1. Insert the barrel connector of the AC charging adapter into the AC charging port on the front of the unit (refer to Fig. 2 to locate). Insert the plug end into a (powered) standard North American 120-volt 60Hz outlet. When the unit is properly connected to an AC power source, the LCD screen will display the following:
   The bars on the Battery Status Icon represent the charge level of the unit’s internal battery. The bars on the Battery Status Icon will change from empty to solid (bottom to top) repeatedly to indicate the unit is charging. The backlight will turn on for 10 seconds (only).
2. Charge for approximately 20 hours or until the Battery Status Icon shows 4 solid bars.
3. When charging is complete, disconnect the AC charging adapter – first unplug the adapter from the AC power source, then disconnect the barrel connector from the unit.

WIRELESS CHARGING

The built-in Wireless Charging feature is suitable for most appliances with a Wireless Charging function. Before proceeding, check the unit’s battery status on the LCD screen. Four solid bars in the battery icon indicate a full battery. When the battery level is nearly empty with only one solid bar, the unit MUST be recharged before use or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period before automatic shutdown.

CAUTION – To reduce the risk of property damage: Do not attempt to use the Jump-Starter or Compressor when using the Wireless Charging function.

IMPORTANT NOTE: 

• If the unit does not detect an appliance for 3 minutes, the Wireless Charging function will shut down automatically.

PROCEDURE

1. Press the Wireless Charging Button to turn on wireless charging. A beep will sound, and the LCD screen will continuously display the following:
   The Battery Status Icon and Battery Voltage Indicator will light solid, and the Wireless Charging Indicator will flash, indicating the Wireless Charging function is ready to use.
2. Place the appliance to be charged in the center of the Wireless Charging Pad for maximum charging efficiency.
3. When charging is complete, press the Wireless Charging Button to turn off the Wireless Charging feature.

IMPORTANT: 

• Make sure the Wireless Charging function is turned off when the unit is being recharged or stored.
• Some appliances may not charge or operate with this unit.

JUMP-STARTER

IMPORTANT:
All features must be turned off except the area light when jump-starting. The unit is intended to be used only in the upright position. The unit must be kept upright during use. See the illustration to the right for the correct orientation.

WARNING – To reduce the risk of serious injury or property damage:

• Follow all safety instructions found in the “Specific Safety Instructions for Jump Starters” section of this instruction manual.
• If the clamps are connected incorrectly about polarity, the unit will sound a continuous alarm until the clamps are disconnected. The backlit LCD Screen will display the Battery Status Icon, the Battery Voltage Indicator, and the Clamp Icons. The “+” and”–” signs above the Clamp Icons, the Reverse Polarity Icons, and the Alarm Icon will flash. The backlit LCD screen will display the following:
  Disconnect the clamps and reconnect to the battery with the correct polarity.
• Never touch red and black clamps together. This can cause dangerous sparks, power arcing, and/or explosions. If the red and black clamps touch each other, the unit will sound a continuous two-second alarm every ten seconds until the clamps are separated. The backlit LCD screen will display the following:
  The Battery Status Icon and Battery Voltage Indicator are light solid. The Alarm Icon, Clamp Icons, and the “+” and”–” signs will flash. Immediately separate the clamps and do not allow them to touch again.
• If the unit is overheated during the jump-starting process, the thermal protection will activate and the backlit LCD screen will display the following:
  The Battery Status Icon and Battery Voltage Indicator are light solid. The alarm icon and Jump Starter Icon will flash. Allow the unit to cool for 10-30 minutes before use.
• Always disconnect the negative (black) jumper cable first, followed by the positive (red) jumper cable, except for positive grounded systems.

Visit: EverStart SL097 Jump Starter or EverStart Maxx EL224

PROCEDURE

Take the following steps, observing all cautions and warnings in the “Important Safety Instructions” section at the front of this manual.

1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place the vehicle in “park” and set the emergency brake.
2. There is a Boost Cables Connector at the end of the clamps. The slot that it plugs into is located on the back of the unit. Refer to the “Features” section to locate. Plug the Boost Cables Connector into the Clamp Connection Slot.
3. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis) (MOST COMMON)
   • Connect the positive (+) red clamp to the vehicle battery’s positive terminal.
   • Connect negative (–) black clamp to the chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to the negative battery terminal or moving part. Refer to the automobile owner’s manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
   NOTE: In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6.
   • Connect the negative (–) black clamp to the vehicle battery’s negative terminal.
   • Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to the positive battery terminal or moving part. Refer to the automobile owner’s manual.
     When the clamps are connected properly, the backlit LCD screen will display the following to indicate the unit is ready to jump-start: The Battery Status icon, Battery Voltage Indicator, Clamp Icons, and the “+” and”–” signs light solid. The EverStart MAXX PPS1CWE 1000 Amp Jump Starter icon will flash to indicate the clamps are properly connected.
6. Turn on the ignition and crank the engine in 5-6 second bursts until the engine starts. The backlit LCD screen will display the following:
   The Battery Status Icon, the Battery Voltage Indicator, Clamp Icons, and the “+” and”–” signs light solid to indicate the unit is jump-starting. The Jump Starter Icon flashes. The EverStart MAXX PPS1CWE 1000 Amp Jump Starter Icon lights solid if the vehicle is started.
7. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
   NOTE: If the unit is malfunctioning after the jump start procedure, please recharge the unit with the supplied AC charger to reset the unit.

IMPORTANT: 

• When the unit is not in use, detach the Boost Cables Connector from the Clamp Connection Slot and store it in a safe place.
• Always turn the unit off when not in use. Recharge this unit fully after each use.

CAUTION – To reduce the risk of property damage:

• Remember to disconnect the clamps from the power station and store them in a dry, safe location when not in use.
• Vehicles that have on-board computerized systems may be damaged if the vehicle battery is jump-started. Before jump-starting this type of vehicle, read the vehicle manual to confirm that external starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails to start after the recommended number of attempts, discontinue the jump-start procedure and look for other problems that need to be corrected.
• If the vehicle fails to start, turn off the ignition, disconnect the jump-start system’s leads, and contact a qualified technician to investigate why the engine did not start.

ALTERNATOR CHECK

Set up the unit, connect the battery clamps, and connect to the battery following steps 1 through 5 under “Procedure” in the “Jump Starter” section.

IMPORTANT NOTES 

• The unit may detect that the alternator is out of the typical voltage range because someone has added several accessory loads on the charging system, thereby increasing current demand from the alternator. MAKE SURE THAT THE ALTERNATOR IS RATED TO SUPPORT THE APPLICATION.
• This check may not be accurate for every make, manufacturer, and model of vehicle. Check only 12-volt systems.

PART 1

No Load (turn OFF all vehicle accessories): The vehicle battery must be fully charged before testing the alternator. Run the engine long enough to achieve normal idle speed and verify there is a no-load voltage.

1. Press the Alternator Check Button to start the check. The backlit LCD screen will display the following to indicate the unit is analyzing the alternator:
   The Battery Status Icon will light solid and the Alternator Icon will flash.
2. If the unit detects that the alternator is good, the backlit LCD screen will display the following:
   The Battery Status Icon, Alternator Icon, and “ALT GOOD” will light solid.
3. If the unit detects that the alternator is out of the typical voltage range, the backlit LCD screen will display the following:
   The Battery Status Icon, Alternator Icon, and “ALT” will light solid. The Fault Icon will flash.
4. Press the Alternator Check Button again to stop the test and turn off the unit.

PART 2

Under Load (accessories ON): Next, load the alternator by turning on as many accessories as possible (except for A/C and Defrost).

1. Press the Alternator Check Button to start the check. The backlit LCD screen will display the following to indicate the unit is analyzing the alternator:
   The Battery Status Icon will light solid and the Alternator Icon will flash.
2. If the unit detects that the alternator is good, the backlit LCD screen will display the following:
   The Battery Status Icon, Alternator Icon, and “ALT GOOD” will light solid.
3. If the unit detects that the alternator is out of the typical voltage range, the backlit LCD screen will display the following:
   The Battery Status Icon, Alternator Icon, and “ALT” will light solid. The Fault Icon will flash.
4. Press the Alternator Check Button again to stop the test and turn off the unit.

IMPORTANT:
Always turn the unit off when not in use. Recharge this unit fully after each use.

CAUTION – To reduce the risk of property damage: 

• Remember to disconnect the clamps from the power station and store them in a dry, safe location when not in use.

PORTABLE COMPRESSOR

The built-in 12-volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires, and recreational inflatables. A nozzle adaptor is supplied that screws onto the end of the Sure Fit® nozzle at the free end of the compressor hose. The compressor hose with tire fitting is stored in the hose storage groove on the rear of the unit. Refer to the “Features” section to locate. The Compressor Power Button and Increase (+) and Decrease (–) Compressor Pressure Control Buttons are located on the control panel on the front of the unit. Before proceeding, check the unit’s battery status on the LCD screen. Four solid bars in the battery icon indicate a full battery.

When the battery level is nearly empty with only one solid bar, the unit MUST be recharged before use or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period before automatic shutdown.
The compressor is capable of inflating up to 120 pounds per square inch (PSI) pressure. Return the hose to the hose storage groove after use.

WARNING – To reduce the risk of serious injury or property damage:
Follow all safety instructions found in the “Specific Safety Instructions for Compressors” section of this instruction manual.

CAUTION – To reduce the risk of serious injury or property damage:
When the compressor is operated at a low PSI, the unit may start at low and gradually rev up. When the compressor is operated at higher PSIs, the unit may operate normally for several minutes, then rev down for a few minutes before returning to normal operation. This feature protects the unit from overheating during normal use. In any event, do not operate the compressor continuously for longer than 10 minutes, as it may overheat. This could damage the compressor. If the compressor must be operated for longer periods: every 10 minutes press the Compressor Power Button to turn the compressor off, then restart after a cooling down period of approximately 30 minutes. In any event, the compressor will automatically shut down after operating continuously for 10 minutes.

INFLATING TIRES OR PRODUCTS WITH VALVE STEMS

1. Screw the Sure Fit® nozzle onto the valve stem. Do not over tighten.
2. Press the Compressor Power Button. A beep will sound and the backlit LCD screen will display the following:
   The Compressor Icon will light and the digital display will alternately show the flashing pre-set psi value (that was last set by the compressor pressure control buttons) and the current pressure of the item being inflated (which will light solid).
3. Press the “+” and “–” Pressure Control Buttons to set the desired pressure from a range of pre-set values (between 3 and 120), which will display on the backlit LCD screen. The unit will sound a beep with each press of the buttons (holding the button speeds up the upward or downward value selection). Once the desired pressure has been entered, release the button and the flashing digital display will show the newly selected pressure, as follows:
   The new selected value is now stored in the unit’s memory until it is manually reset.
4. Press the Compressor Power Button once more to begin inflating. The Compressor Icon will flash and the digital display will only show the current pressure value
   (which will be light solid) to indicate the compressor is activated. Monitor the pressure on the LCD screen.
   IMPORTANT NOTE: To interrupt during inflation, press the Compressor Power Button again.
5. When the desired pre-set pressure is reached, the compressor will automatically stop.
6. Press the Compressor Power Button again to turn off the unit.
7. Unscrew and remove the Sure Fit® nozzle from the valve stem.
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and Sure Fit® nozzle in the storage groove.

INFLATING OTHER INFLATABLES WITHOUT VALVE STEMS

Inflation of other items requires the use of the nozzle adapter.

1. Screw the nozzle adapter into the Sure Fit® nozzle. Do not over tighten.
2. Insert the nozzle adapter into the item to be inflated.
3. Follow steps 2 through 4 of the “Inflating Tires or Products With Valve Stems” section.
   IMPORTANT: Small items such as volleyballs, footballs, etc. inflate very rapidly. Keep this in mind when setting pressure. Take extra care not to over-inflate.
4. When the desired pressure is reached, the compressor will automatically stop. Press the Compressor Power Button again to turn off the unit.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the Sure Fit® nozzle.
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, Sure Fit® nozzle, and nozzle adapter in the storage groove.

Visit: EverStart SL097 Jump Starter

USB PORTS

The USB Power Button and the two USB Ports are located on the front of the unit; the USB Power/Fault Indicator is a translucent ring around each of the USB Ports. Refer to the “Features” section to locate.

IMPORTANT NOTES 

1. The two USB Ports provide a total of 3.1A (5V each).
2. When the USB Ports are in use, the unit will monitor for the following USB fault conditions on both USB Ports: low battery voltage fault, overload, and short circuit. If a low battery voltage fault occurs, the USB Power/Fault Indicators will turn off. The LCD screen will display the Battery Status Icon and the Voltage Icon for 10 seconds before the unit shuts down automatically. If an Overload Fault or Short-circuit occurs in either of the USB Ports, the USB Power/Fault Indicators will flash blue. In any of these cases, the backlit LCD screen will continuously display the following:
   The Fault Icon will flash. The USB Ports will automatically shut down. Should this occur:
   • a. Disconnect the USB-power device and press the USB Power Button again to turn off the USB Ports immediately.
   • b. Make sure the unit does not need to be recharged.
   • c. Allow the unit to cool down for several minutes before attempting to use the USB Ports again.
   • d. If an individual USB device is within specifications and the fault occurs, have the USB device checked for malfunction and
   • do not continue to use it with these USB Ports.
3. This unit’s USB Ports do not support data communication. They only provide power to external USB-powered devices.
4. Some household USB-powered electronics will not operate with this unit.

USING THE USB PORTS

1. Press the USB Power Button to turn on both USB Ports. A beep will sound, the USB Power/Fault Indicators around each of the USB Ports will light blue and the LCD screen will continuously display the following:
   The Battery Status Icon and Battery Voltage Indicator will light solid, as well as the USB Icon, indicating the USB ports are ready to use.
2. Plug the USB-powered device into the USB power port(s) and operate normally.
3. Press the USB Power Button again to turn off the USB Ports.

Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in the battery icon indicate a full battery. When the battery level is nearly empty with only one solid bar or empty with 4 empty bars, the unit must be recharged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period before automatic shutdown.

IMPORTANT:
Make sure the USB Ports are turned off when the unit is being recharged or stored.

LED AREA LIGHT

The built-in LED Area Light is controlled by the area light on/off button on the control panel. Refer to the “Features” section to locate.

1. Press the Area Light Power Button once to turn the light on.
2. Press the Area Light Power Button again to turn the area light off.

When the Area Light Power Button is pressed to turn it on, a beep will sound. The backlit LCD screen will turn on for 10 seconds (only) and will then continuously display the Battery Status Icon and the Battery Voltage Indicator. Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in the battery icon indicate a full battery. When the battery level is nearly empty with only one solid bar or empty with 4 empty bars, the unit must be recharged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period before automatic shutdown.

IMPORTANT:
Make sure the Area Light is turned off when the unit is being recharged or stored.

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we recommend that the battery be charged at least every 30 days. From time to time wipe the outside of the appliance with a soft cloth. Do not immerse the appliance in water. There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors, and wires. Contact the manufacturer to replace any components that have become worn or broken.

Visit: EverStart JUS750CE Jumper Starter

BATTERY REPLACEMENT/DISPOSAL

Battery
Please be advised that the battery is designed to last the service life of the unit and is not replaceable, removable, or serviceable. Service life is dependent on several factors including but not limited to the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact the manufacturer for any information you may need.

SAFE BATTERY DISPOSAL

Contains a maintenance-free, sealed, non-spoilable, lead acid battery, which must be disposed of properly. Recycling is required. Failure to comply with local, state, and federal regulations can result in fines or imprisonment. Please recycle.

WARNING: 

• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose the battery to fire or intense heat as it may explode.

TROUBLESHOOTING

ACCESSORIES

Recommended accessories for use with your tool may be available from the manufacturer. If you need assistance regarding accessories, please contact the manufacturer at 1-877-571-2391.

WARNING:
The use of any accessory not recommended for use with this appliance could be hazardous.

SERVICE INFORMATION

Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391.

TWO-YEAR LIMITED WARRANTY

The manufacturer warrants this product against defects in materials and workmanship for a period of TWO (2) YEARS from the date of retail purchase by the original end-user purchaser (“Warranty Period”). If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways:

1. Return the product to the manufacturer for repair or replacement at the manufacturer’s option. Proof of purchase may be required by the manufacturer.
2. Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required.

Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product. This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to state or province to province. This product is not intended for commercial use.

APPENDIX

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and candidate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and any other radio device.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

SPECIFICATIONS

• Boost Ampere: 1,000A peak, 350A instant
• Battery Type: SLA, 12V DC
• Input: 120V AC, 60Hz, 14W
• Compressor: 120 PSI (max.)
• USB Output: 5V DC each, 3.1A (max.)
• Wireless Charging: 10W (max.)

Sure Fit® is a registered trademark owned by Baccus Global, LLC.
Imported by Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.Baccusglobal.com 1-877-571-2391
RD051821

Visit: EverStart maxx EL224

FAQ’s EverStart MAXX PPS1CWE 1000 Amp Jump Starter

You may also want to visit other jump starters from EverStart:

• EverStart JUS750CE Jumper Starter
• EverStart SL097 Jump Starter
• EverStart maxx EL224