ASRock H510M-HDV Compatible with Intel 10th and 11th Generation CPUs User Manual

ASRock H510M-HDV Compatible with Intel 10th and 11th Generation CPUs

Introduction

Thank you for purchasing ASRock H510M-HDV/M.2 SE motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

Package Contents

• ASRock H510M-HDV/M.2 SE Motherboard (Micro ATX Form Factor)
• ASRock H510M-HDV/M.2 SE User Manual
• 1 x I/O Shield
• 2 x Serial ATA (SATA) Data Cables (Optional)
• 1 x Screw for M.2 Socket (Optional)

Specifications

Platform

• Micro ATX Form Factor

CPU

• Supports 10th Gen & 11th Gen Intel® CoreTM Processors (LGA1200)
• Supports Intel® Turbo Boost Max 3.0 Technology

Chipset

• Intel® H470

Memory

• Dual Channel DDR4 Memory Technology
• 2 x DDR4 DIMM Slots
• Supports DDR4 3200/2933/2800/2666/2400/2133 non-ECC, un-buffered memory*
• Supports ECC UDIMM memory modules (operate in nonECC mode)
• Max. capacity of system memory: 64GB
• Supports Intel® Extreme Memory Profile (XMP) 2.0
• 15μ Gold Contact in DIMM Slots

Graphics

• Intel® UHD Graphics Built-in Visuals and the VGA outputs can be supported only with processors that are GPU integrated.
• Graphics specifications may vary between CPU types.
• 1 x HDMI Intel® 11th Gen Processors support HDMI 2.0, HDCP 2.3 and max. resolution up to 4K 60Hz Intel® 10th Gen Processors support HDMI 1.4, HDCP 2.3, and max. resolution up to 4K 30Hz
• 1 x DVI-D, supports HDCP 2.3 and max. resolution up to Full HD (1920×1200) 60Hz
• 1 x D-Sub, supports max. resolution up to Full HD (1920×1200) 60Hz

Audio

• 7.1 CH HD Audio (Realtek ALC897 Audio Codec)

LAN

• Gigabit LAN 10/100/1000 Mb/s
• Realtek 8111H

USB

• 6 x USB 3.2 Gen1 (4 Rear, 2 Front)
• 6 x USB 2.0 (2 Rear, 4 Front)

Storage

• 1 x Ultra M.2 Socket (M2_1, Key M), supports type 2260/2280 SATA3 6.0 Gb/s & PCIe Gen3x4 (32 Gb/s) modes*
• 4 x SATA3 6.0 Gb/s Connectors

RAID

• Supports RAID 0, RAID 1, RAID 5, and RAID 10 for SATA storage devices

Connector

• 1 x COM Port Header
• 1 x SPI TPM Header
• 1 x Chassis Intrusion and Speaker Header
• 1 x CPU Fan Connector (4-pin)*
• 1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan Speed Control)**
• 2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan Speed Control)***
• 1 x 24-pin ATX Power Connector
• 1 x 8 pin 12V Power Connector
• 1 x Front Panel Audio Connector
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports)
• 1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)

Motherboard Layout

1. ATX 12V Power Connector (ATX12V1)
2. CPU Fan Connector (CPU_FAN1)
3. 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4. Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
5. ATX Power Connector (ATXPWR1)
6. USB 3.2 Gen1 Header (USB32_5_6)
7. SATA3 Connectors (SATA3_0)(Upper), (SATA3_1)(Lower)
8. SATA3 Connectors (SATA3_2)(Upper), (SATA3_3)(Lower)
9. SPI TPM Header (SPI_TPM_J1)
10. System Panel Header (PANEL1)
11. Chassis Intrusion and Speaker Header (SPK_CI1)
12. Chassis/Water Pump Fan Connector (CHA_FAN2/WP)
13. USB 2.0 Header (USB_5_6)
14. USB 2.0 Header (USB_3_4)
15. Clear CMOS Jumper (CLRMOS1)
16. COM Port Header (COM1)
17. CPU/Water Pump Fan Connector (CPU_FAN2/WP)
18. Front Panel Audio Header (HD_AUDIO1)

I/O Panel

1. D-Sub Port
2. PS/2 Mouse/Keyboard Port
3. LAN RJ-45 Port*
4. Line In (Light Blue)**
5. Front Speaker (Lime)**
6. Microphone (Pink)**
7. USB 3.2 Gen1 Type-A Ports (USB32_34)
8. USB 2.0 Ports (USB_12)
9. USB 3.2 Gen1 Type-A Ports (USB32_12)
10. DVI-D Port
11. HDMI Port

Block Diagram

Installation

This is a Micro ATX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.

• Make sure to unplug the power cord before installing or removing the motherboard components. Failure to do so may cause physical injuries and damage to motherboard components.
• To avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also, remember to use a grounded wrist strap or touch a safety-ground object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.

Installing the CPU

Installing the CPU Fan and Heatsink

Connecting the Front Panel Header

Installing the I/O Panel Shield

Installing the Motherboard

Installing SATA Drives

Installing a Graphics Card

Copyright Notice

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form, or by any means, except duplication of documentation by the purchaser for backup purposes, without the written consent of ASRock Inc. Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owner’s benefit, without intent to infringe.

Disclaimer

Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation. Concerning the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business, and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

SOFTWARE LICENSE AGREEMENT

LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Software only in its unmodified and binary form, (with the accompanying documentation, the “Software”) for Licensee’s personal use only, and not commercial use, in connection with Intel-based products for which the Software has been provided, subject to the following conditions:

• Licensee may not disclose, distribute, or transfer any part of the Software, and You agree to prevent unauthorized copying of the Software.
• Licensee may not reverse engineer, decompile, or disassemble the Software.
• Licensee may not sublicense the Software.
• The Software may contain the software and other intellectual property of third-party suppliers, some of which may be identified in, and licensed by, an enclosed license.txt file or other text or file.
• Intel has no obligation to provide any support, technical assistance, or updates for the Software.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS
Title to all copies of the Software remains with Intel or its licensors or suppliers. The Software is copyrighted and protected by the laws of the United States and other countries, and international treaty provisions. Licensee may not remove any copyright notices from the Software. Except as otherwise expressly provided above, Intel grants no express or implied right under Intel patents, copyrights, trademarks, or other intellectual property rights. Transfer of the license terminates the Licensee’s right to use the Software.

DISCLAIMER OF WARRANTY
The Software is provided “AS IS” without warranty of any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF LIABILITY
NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS
This Agreement does NOT obligate the Licensee to provide Intel with comments or suggestions regarding the Software. However, if the Licensee provides Intel with comments or suggestions for the modification, correction, improvement, or enhancement of (a) the Software or (b) Intel products or processes that work with the Software, the Licensee grants to Intel a non-exclusive, worldwide, perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments and suggestions.

TERMINATION OF THIS LICENSE
Intel or the sublicensor may terminate this license at any time if the Licensee is in breach of any of its terms or conditions. Upon termination, Licensee will immediately destroy or return to Intel all copies of the Software. THIRD-PARTY BENEFICIARY

Intel is an intended beneficiary of the End User License Agreement and has the right to enforce all of its terms.

EXPORT LAWS
Licensee agrees that neither Licensee nor Licensee’s subsidiaries will export/re-export the Software, directly or indirectly, to any country for which the U.S. Department of Commerce or any other agency or department of the U.S. Government or the foreign government from where it is shipping requires an export license, or other governmental approval, without first obtaining any such required license or approval. In the event the Software is exported from the U.S.A. or re-exported from a foreign destination by Licensee, Licensee will ensure that the distribution and export/re-export or import of the Software complies with all laws, regulations, orders, or other restrictions of the U.S. Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS
This Agreement and any dispute arising out of or relating to it will be governed by the laws of the U.S.A. and Delaware, without regard to conflict of laws principles. The Parties to this Agreement exclude the application of the United Nations Convention on Contracts for the International Sale of Goods (1980). The state and federal courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising out of or relating to this Agreement. The Parties consent to personal jurisdiction and venue in those courts. A Party that obtains a judgment against the other Party in the courts identified in this section may enforce that judgment in any court that has jurisdiction over the Parties.

For more Manuals by ASROCK, visit MANUALSDOCK