Abestorm DecDust 1350 360 Degree Intake Air Filtration System
About Abestorm
Abestorm Crawl Space NeatyFresh Max allows for the free circulation of air on the porch and under the house. High moisture levels in the crawl spaces can lead to the decay and rot of wooden pillars that support the house, floor, joists, and beam pillars. Also, high humidity causes an increase in termite activity and the growth of fungi. Rust, which causes corrosion and leaks in metallic pipes, is also factored into the moisture level in your crawl space.
With our ventilation fan, radon gas from treated wood is expelled away. This gas and other odors can easily spread into the living room and cause discomfort. The NeatyFresh Max fan uses a humidity switch to control the fan to commence operation. The fan starts operating when the recorded humidity surpasses the selected value.
WHAT’S IN THE BOX
- DecDust 1350 / 13501G x 1
- MERV-11 Filter x 4
- Hanging Piece x 4
- Nut x 4
- Hooks x 4
- Controller x 1
- User’s Manua x 1
- Screw x 4
- Expansion Bolt x 4
- Screw Hooks x 4
- Hanging Chains x 4
- battery x 2
DESCRIPTION
Your new tool has been engineered and manufactured to Abestorm’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you with ears of rugged, trouble-free performance.
Pay close attention to the rules for safe operation, warnings, and cautions. if you use your tool properly and for the intended purpose, you will enjoy years of safe, reliable service.
HOW IT WORKS
- Connect the dust collector to a standard 115V/60Hz outlet.
- Refrain from moving the unit during operation.
- Keep both air inlet and outlet away from the wall or any obstructions for at least 2 ft.
- This product can only filter dust particles above 1μm.
SAFETY RULES
WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood.
- DO NOT use power tools in the presence of flammable liquids or gases.
- KEEP BYSTANDERS ATASAFE DISTANCE from the work area, especially when the tool is operating. NEVER allow children or pets near the tool.
- DRESS FOR SAFETY. Do not wear loose clothing, gloves, neckties, or jewelry (rings, watches, etc.) when operating the tool. inappropriate clothing and items can get caught in moving parts and draw you in. ALWAYS wear non-slip footwear and tie back long hair.
- WEAR A FACE MASK OR DUST MASK to fight the dust produced by sawing operations
ELECTRICAL SAFETY
EQUIPMENT MUST BE GROUNDED
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock.
This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet properly installed and grounded by ALL local codes and ordinances.
KNOW YOUR AIR FILTRATION SYSTEM
Carefully unpack the air filter and all its parts. Do not discard the carton or any packaging until the air filter is completely assembled.
ASSEMBLY AND ADJUSTMENTS
The air filter is designed to circulate and filter wood and other non-metallic dust. The unit requires only minimal assembly. However, it is important to consider how and where to place the unit. When selecting a site, ensure a suitable power source is nearby. Do not use extension cords with the air filter.
INSTALLATION METHOD #1 (Fig. 1):
- Thread the locknuts â‘ almost up the hanger â‘¡.
- Thread a hanger into each of the four mounting holes â‘¢ on the top of the air filter cabinet.
- Tighten the catch locknut against the cabinet top. Hold the hangers so that they do not spin while tightening the locknut.
CEILING PLACEMENT (Fig. 2)
Make sure the unit will be situated at least 7′ above the floor and at least 3′ away from a corner and any heating or air vents. (CEILING PLACEMENT – Fig. 2)
- Create a marking on the ceiling where you will be installing the hook. (recommended installation size: 23.6 × 23.6 inches, 60 × 60 cm.)
- On the marked spots on the ceiling, use a 3mm drill bit to create a hole.
- Install the wood screw hooks â‘¡ into the building support structureâ‘ . Do not mount the air filter to non-structural surfaces such as drywall or false ceiling grids. The hooks are rated for this air filter and can support a maximum of 100 lbs.
- Place a chain â‘¢ on each wood screw hook â‘¡.
- Attach the hangers on each chainâ‘¢.
- Make sure the unit is level horizontally and is at least 7′ above the floor if it is not, remove the air filter and adjust the length of the chain as needed. Then remount the unit.
- Plug the air filter power cord directly into a power source.
INSTALLATION METHOD #2 (Fig. 3):
Make sure the unit will be situated at least 7′ above the floor and at least 3′ away from a corner and fny heating or air vents.
- Use the M4 screws to install 4 mounting brackets onto the equipment
- Measure the distance between brackets and use it as a guide to create a marking on the ceiling before the installation. (recommended installation size: 18.9 × 18.9 inches, 48 × 48 cm.)
- On the marked spots, use a 10mm drill bit to make a hole for the insertion of the expansion screws to the ceiling.
- Carefully lift the equipment to insert the ceiling-attached expansion screw into the hole of the mounting brackets. Use the nut to secure the mounting back and the machine on the ceiling.
NOTE: The above installation must be installed by no less than two people! For a step-by-step video tutorial, search the URL provided below using your computer browser.
The guide starts at 1:12 of the video.
When you install the unit, you may also put the air outlet up. (You need to remove the control panel, and turn around 180°, then install back again.)
OPERATION
The air filter can be operated directly using the control panel or with the remote control. The Air filter with power off memory function, power off after the boot again, will repeat the last operation.
TURN ON AIR FILTER AND SPEED SETTINGS (Fig.3 and 4)
- Plug the power cord into an appropriate power source.
- Press the “On/Off” button on the control panel or the “On/Off” button on the remote control to switch On the POWER supply of the air filter. The POWER indicator light is On, and the dust filter is operated before the last shutdown (except the scheduled shutdown).
- Press the “SPEED” button on the control panel or the â‘©button on the remote control to set the SPEED of the dust filter and the SPEED selected by the LOW/HIGH â‘£/â‘¥indicator on the control panel.
- Press the ionizer button on the remote control to turn the ionizer indicator (5)on or off.
- Press the timer shutdown button on the remote control to enter the timer shutdown.
- The infrared receiving opening ⑧ on the control panel should not be blocked by objects or dirt.
MAINTENANCE
WARNING: To reduce the risk of injury and electric shock, unplug the air filtration system from the power source before changing the air filters or servicing the unit.
CHANGE THE FILTERS
Check the inner and outer filters periodically, depending on the amount of use, and change the filters when needed. Clogged filters will reduce the amount of air circulating through the filter.
- When the device is powered off, take it to the middle of the filter and take it out externally.
- Take out the new filter and place it in the device according to the direction indicated.
Replacement filters for this unit are available at （www.abestorm.com） and all online retailers where this unit is sold.
CHECK AND TROUBLESHOOT
- According to your operating environment, the equipment may be blocked by the filter, resulting in noise. Please replace the filter in time.
- Excessive current or abnormal family circuit will lead to the power off protector being connected. Equipment power, protect your circuit.
POWER-OFF PROTECTION RECOVERY
- Disconnect the power supply.
- Press the circuit breaker â‘ back to its original position.
- Switch on the power supply and start the machine.
WIRING DIAGRAM
SPECIFICATIONS
- Motor 115V/60Hz 1.5Amps Max
- Air Flow Speeds 1050CFM(LOW) 1350CFM(HI)
- Filters MERV-11 (90% 3-10 microns 85% 1 micron)
- Maximum Remote Control Distance 27Ft
- Weight 27lbs
- Dimensions (W x H x D) 20.5″ x 20.5″ x 9.8″ (inch)
LIMITED WARRANTY
The limited warranty applies to the original purchaser only, from the date of purchase. It should be subject to the terms and conditions listed in this limited warranty file.
WARRANTY PERIOD
The warranty becomes effective from the date of the original purchase and will last for one year. This limited warranty is not transferable. It is only valid for the original purchaser.
Warranty debarment:
- Damage caused by the owner when attempting to fix or alter the product by himself or herself.
- Damage caused by misuse, abuse, neglect, alterations, or unauthorized repair.
- Natural depreciation.
Abestorm Warranty Steps:
To obtain the benefit of this warranty, please leave your message online web: (www.abestorm.com) or send an email to sales@abestorm.com.
Our customer service will address your issue between Mon-Fri 7:00 AM to 4:00 PM PST.
- Upon receiving this item, visit www.abestorm.com and fill out the warranty registration form. The order number is required to submit a warranty claim.
- To request warranty service, contact sales@abestorm.com.
- After receiving the warranty service request, our customer support team will investigate the issue, Here, will be determined if a Return authorization is necessary.
- If the damage to the machine is proven to be one of the warranty exclusions (Page 10), Abestorm will not be responsible for all the associated repair and shipping costs. The eligibility of a replacement unit will also be voided.
- If the damaged unit that can no longer be fixed is within the warranty period, Abestorm will handle all the costs of sending a brand-new replacement unit.
- When the unit is repaired or replaced, the original warranty period carries over to the repaired or new unit. No warranty extensions will be offered.
- IMPORTANT NOTICE: Keep the item’s packaging in case warranty service is required.
WARRANTY EXCLUSIONS
DAMAGE DUE TO THE FOLLOWING IS NOT covered under warranty:
- Acts of Nature- including but not limited to:
- Flooding
- Fire
- Water damage
- Hurricane/storm damage
- IMPROPER USAGE- Including but not limited to:
- Misuse, abuse, or tampering whether intentional or accidental
- improper installation
- improper voltage
- improper maintenance
- Failure to follow instructions
- Corrosion
- Freezing
- Any additional costs due to changes in laws or building codes
- Freight charges
- Any costs due to lost profit or delay
- Damage to property
- Cause beyond control
- Consumable parts, including but not limited to:
- Filters
- Power cords
- Switches
- Batteries
- Valves
- Rubber parts
- Direct, indirect, collateral, or inconsequential damages of any kind.
Any dishonesty or fraud in connection with the Abestorm warranty thoroughly voids all warranty policies. Abestorm expressly reserves the right to pursue legal action in the event of dishonesty, fraud, or attempted fraud.
Abestorm Solutions INC.
Add: 8605 SANTA MONICA BLVD#79525 WEST HOLLYWOOD, California, 90069 USA
Tel: +1 888-276-9833
E-mail:Â sales@abestorm.com
website:Â www.abestorm.com
FAQs About Abestorm DecDust 1350 360 Degree Intake Air Filtration System Woodworking
What size system of dust filtering is required?
Use this formula to calculate the necessary airflow or size: The area measured by length, breadth, and height of your workshop multiplied by the number of air exchanges per hour (preferably between 6 and 8) and divided by 60.
In a woodshop, where is the air filter located?
How and where you attach the air cleaner is just as crucial as its dimensions. Aim for a mounting height of 8 to 10 feet (no lower than 6 feet, or 2/3 of the floor-to-ceiling distance if the ceiling is lower than 8 feet). Place the intake about one-third the distance from the shorter wall by mounting it along the longest wall.
How is the air in a workshop cleaned?
There are a few different ways to accomplish this. Initially, an air filtration device (AFD) that collects fine floating dust in the air ought to be installed in every workshop. In addition, it’s critical to vacuum the workshop regularly and to use a vacuum with a HEPA filter.
What is the capacity of an air filter?
The mass of synthetic test dust that an air filter can hold onto until it reaches the desired final pressure drop increase is known as its dust retention capacity.
How much of an air filtering system should a workshop have?
The airflow required for your shop may be calculated by multiplying the length, width, and ceiling height. The cubic foot of your shop is the outcome. After that, divide this amount by ten. This represents the cubic feet per minute that your shop requires.
Can you wash air filters?
You can wash some types of filters, yes! This implies that you can clean the dust and debris off of your air filter and reinstall it in your HVAC system after its three-month lifespan has passed rather than discarding it. Before submerging it, make sure the filter is washable as not all filters are reusable.
In terms of air filtration, what is CFM?
The most often used unit of measurement for airflow is CFM or cubic feet per minute. The amount of air a room’s air purifier system filters is measured in CFM. The volume of air movement at a specific moment in a minute is measured in cubic feet. An air purifier can filter more air in a room the higher its CFM.
In a woodshop, how is dust management achieved?
To collect dust as it is produced, fit extraction apertures and dust hoods to your woodworking equipment. This minimizes the quantity of dust that enters the air and accumulates on surfaces by preventing it from spreading throughout the workshop.
What prevents dust from adhering to wood?
One unique tip to create the illusion of a dust-free space is to dust your hardwood furniture with a dryer sheet after you’ve cleaned it using the previously described cloth. Not only would the drier sheet give the appearance of cleaner furniture, but it will also keep dust from adhering to the wooden surfaces.
Is it possible to clean and reuse air filters?
Certain air filters, both permanent and semipermanent, can be changed for continued usage and cleaned as part of routine HVAC system maintenance. On the other hand, a disposable air filter functions differently. It needs to be taken out of the HVAC cabinet, thrown away, and replaced with a new filter on a regular basis.
For more Manuals by ABESTROM, visit MANUALSDOCK