Welcome to ManualsDock! Read Millions of manuals for free.

Get 20% off and boost your website's speed with Hostinger Cloud Hosting!

Keurig K-Iced Single Serve Coffee Maker User Manual


Keurig LOGO

Keurig K-Iced Single Serve Coffee Maker

Keurig K-Iced Single Serve

Before You Brew

  1. Plug & Place
    Remove the packing tape from the brewer. Plug into an outlet. Place a large mug (10oz minimum) on the drip tray.Keurig K-Iced Single Serve .4
  2. Rinse & Fill
    Remove the water reservoir lid, then lift the reservoir straight up to remove it. If you have a Keurig® Water Filter (sold separately), install it now. Refer to your Water Filter Starter Kit for instructions. Rinse the reservoir with fresh water and fill it to the MAX FILL line. Replace the water reservoir, making sure the tank is seated properly in the base. Replace lid.Keurig K-Iced Single Serve 1
  3. Lift & Lower
    Lift and lower the handle. Do not insert a K-Cup® pod. The brewer will power on automatically.Keurig K-Iced Single Serve 2
  4. Cleansing Brew
    The 3-cup sizes will blink. Press the 8oz button to start a cleansing brew. Pour the hot water into the sink. Do not remove the water reservoir or lift the handle once the brew button has been pressed until the brew has been completed. The one-time setup process is now complete and you are ready to brew!Keurig K-Iced Single Serve 3

Brewer Features

    Brew a refreshing iced coffee in minutes. The BREW OVER ICE feature automatically adjusts brew temperature — starting hotter to help extract full flavor, then cooling down for less ice melt.
    For a bolder, more intense cup.
    Coffee is made in minutes.
    Immediately brew a second cup;  no need to wait to reheat
    Accommodates travel mugs up to 7.25” tall.
    Just insert any K-Cup® pod and use the button controls to brew a delicious cup.
    Reminds you to descale after every 250 brews. COMPATIBLE WITH THE MY K-CUP® UNIVERSAL REUSABLE
    Brew your ground coffee (sold separately).
    Once in mode, follow the guided process to  effectively remove scale from your brewer
    Automatically turns your brewer off 5 minutes after the last brew for energy savings, but will be ready to brew as soon as it is powered on again.
    To ensure your brewer works properly at higher altitudes (5,000 feet), please enable the High Altitude Brewing Mode on your brewer.
  1. Begin with the brewer plugged in and powered off.
  2. Press and hold the POWER button and 10oz button for 3 seconds. The 12oz button will illuminate to confirm that the High Altitude Brewing Mode has been enabled.
  3. High Altitude Mode will remain enabled until steps 1-2 are repeated the 12oz light turns off and the 8oz light turns on to confirm that the High Altitude Brewing Mode is disabled.

While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle.

Caring For Your Brewer

Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning. 

  • Brewer Exterior
    Keep your Keurig® brewer looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, nonabrasive cloth. Never immerse the brewer in water or other liquids.
  • Water Reservoir
    The water reservoir should be cleaned periodically by wiping the inside of the reservoir and the underside of the lid with a damp, nonabrasive, lint-free cloth. Do not dry the inside of the water reservoir with a cloth, as lint may remain. Allow the reservoir to dry completely. Hand-wash only.
  • Drip Tray
    The drip tray overflow should be emptied and cleaned occasionally. To remove, lift off the brewer base, keeping it level to avoid spilling. Rinse and clean with a damp, soapy, lint-free, nonabrasive cloth. Hand-wash only.

Regular Maintenance
For great-tasting coffee, keep your brewer running at peak performance by following the recommended maintenance schedule:

Keurig K-Iced Single Serve 4

  • K-Cup® Pod Holder
    To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the top of the K-Cup® pod holder with one hand while pushing up on the bottom of the K-Cup® pod holder from underneath with the other until it releases. After cleaning, align theK-Cup® pod holder with the opening, using the two front ribs as a guide, and snap into place from the top.
  • Exit Needle
    Remove the pod holder assembly and detach the funnel. Locate the exit needle on the inside bottom of the K-Cup® pod holder. Insert a straightened paper clip into the exit needle to loosen any coffee grounds.
  • Funnel 
    Washing the funnel ensures a fresh beverage experience. The funnel should be washed regularly and can be removed from the K-Cup® pod holder by pulling on it until it pops off. To replace it, orient the snaps to the indent and just snap it back onto the K-Cup® pod holder.
  • Entrance Needle
    Lift the brewer handle and locate the entrance needle on the underside of the lid. To clean the holes in the needthe hthe brewer ewer handle in the upward position, and with your other hand, carefully insert a straightened paper clip into all the holes. Gently move it around to loosen any coffee grounds. Low the handle completely and run a cleansing brew two times. Do not insert a K-Cup® pod.

Descaling Procedure

The full descaling procedure must be completed to turn off the Descale light.

You will need:
a large ceramic mug (14oz minimum), fresh water, Keurig® Descaling Solution, and access to a sink. Do not use a paper cup. Ensure that there is no beverage pod in the K-Cup® pod holder. The descaling procedure takes approximately 20 minutes.

The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see little to no output dispensed, followed by the sound of air blowing out. If this occurs:

  • Turn off and unplug the brewer.
  • If there is Keurig® Descaling Solution in the water reservoir, discard the contents, rinse the water reservoir thoroughly, and refill it with water.
  • Plug the brewer back in, power it on, and repeat the Step 3 Fresh Water Rinse cycle. The brewer should begin to function normally as the solution is rinsed out and the scale is removed. If the problem persists, allow the brewer to sit unplugged for at least 30 minutes before continuing with the rinse.


Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool.

  • Clean the exit needle of the K-Cup® pod holder. Refer to the exit needle care instructions.
  • Clean the brewer entrance needle. Refer to the entrance needle care instructions.

For optimal enjoyment and to limit grounds in your cup during hot water brews or when transitioning from brewing coffee pod to a non-coffee pod (e.g., tea or cocoa), clean the exit and entrance needles per the instructions provided and perform two cleansing brews.

Brewing a Partial Cup

  • BREW OVER ICE dispense volume includes ice melt. The BREW OVER ICE setting automatically adjusts brew parameters to take into account ice melt, delivering the desired beverage with a final volume equal to the selected brew size.
  • Unplug the brewer and plug it back in to put the brewer in an idle state (all lights off). Press and hold the 12oz button for 5 seconds until water starts dispensing. Then release and let the water purge. Discard the contents into the sink.
  • The exit needle may be clogged. Refer to the exit needle care instructions.
  • Clean the K-Cup® pod holder; see K-Cup® pod holder care instructions.
  • The brewer may need to be described. If you have repeated the descaling procedure on your brewer two times and it is still only brewing a partial cup, contact Customer Service.
  1. Helpful Hints
    Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water.
  2. Service
    Beyond these recommended cleaning and maintenance procedures, this brewer is not user-serviceable. For service, please refer to the Warranty section of this guide.
  3. Storage
    Empty the water reservoir before storing or transporting and take care to ensure that you store your brewer in a safe and frost-free environment. When you prepare to use it after storage, we recommend rinsing the water reservoir with fresh water and descaling the brewer as detailed in the DescalingProcedure section. If you plan to move your brewer to a different location, turn the brewer off, unplug it, and empty the water reservoir. If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using it.


Keurig Green Mountain, Inc. (Keurig) warrants that your brewer will be free of defects in materials or workmanship under normal home use for one year from the date of purchase. It is recommended that you register your brewer on keurig.com/new so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase. If a replacement brewer is necessary to service this warranty, the replacement brewer may be new or reconditioned. If a replacement brewer is sent, a new limited one-year warranty will be applied to the replacement brewer.

This warranty only applies to brewers operated in the United States and Canada. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the case of Canada, from province to province. Only the use of Keurig® K-Cup® brand pods and accessories will guarantee the proper functioning and lifetime of your Keurig®brewer. Any damage to or malfunction of your brewer resulting from the use of non-Keurig® pods and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use.

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or province of purchase. Nor does this warranty cover damages caused by the use of non-Keurig® pods or accessories, services performed by anyone other than than Keurig or its authorized service providers, use of parts other than genuine Keurig® parts, or external causes such as abuse, misuse, inappropriate power supply, or acts of God.

THIS WARRANTY IS EXCLUSIVE AND IS INSTEAD OF ANY OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES CONCERNING YOUR KEURIG® BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the state or the province of purchase.

Keurig® brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. However, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll-free phone number, 1-866-901-BREW (2739). Please do not return your brewer for servicing without first speaking to Keurig Customer Service to obtain a Return Materials Authorization (RMA) number. Keurig® brewers returned without an RMA number will be returned to the sender without servicing.


Keurig K-Iced Single Serve 5

  • Handle
  • K-Cup® Pod Holder Assembly
  • Drip Tray Plate
  • Drip Tray
  • Drip Tray Base
  • Water Reservoir Lid
  • Water Reservoir


Leave a Comment