EnGenius N300 Access Point Up to 300 Mbps User Manual

EnGenius N300 Access Point Up to 300 Mbps

About EnGenius
EnGenius Technologies is a company specializing in wireless communications and networking solutions. Established in 1999, EnGenius has been at the forefront of delivering robust and reliable wireless technology for various industries and applications.

Introduction

EAP300 is a multi-functioned 11n product with 3 major multi-functions, is designed to operate in every working environment for enterprises. EAP300 is a Wireless Network device that delivers up to 6x faster speeds and 7x extended coverage than 802.11b/g devices. EAP300 supports home networks with superior throughput, performance, and unparalleled wireless range. To protect data during wireless transmissions, EAP300 encrypts all wireless transmissions through WEP data encryption and supports WPA/WPA2. Its MAC address filter allows users to select stations with access to connect network. In addition, the function of user isolation protects the private network between client users. EAP300 thus is the best product to ensure network safety for enterprises.

Features and Benefits

Features	Benefits
High-Speed Data Rate Up to 300Mbps	Capable of handling heavy data payloads such as MPEG video streaming.
10/100 Fast Ethernet	Support up to 100Mbps networking speed.
IEEE 802.11n draft Compliant and backward compatible with 802.11b/g	Fully compatible with IEEE 802.11b/g/n devices.
Multi-Function, 3 functions	Allowing users to select AP, WDS AP, or WDS Bridge mode in various applications.
Point-to-point, Point-to-multipoint Wireless Connectivity	Allowing to transfer of data from buildings to the building.

Support Multi-SSID function (4 SSID) in AP mode	Allowing clients to access different networks through a single access point and to assign different policies and functions for each SSID by manager.
WPA2/WPA/ IEEE 802.1x support	Powerful data security.
MAC address filtering in AP mode	Ensuring secure network connection.
User isolation support (AP mode)	Protecting the private network between client users.
Power-over-Ethernet (IEEE802.3af)	Flexible Access Point locations and saving cost.
Keep personal setting	Keeping the latest setting when firmware upgrade.
SNMP Remote Configuration Management	Helping administrators to remotely configure or manage the Access Point easily.
QoS (WMM) support	Enhancing user performance and density.

 

Package Contents

The package contains the following items. In case of a return, please keep the original box set and the complete box set must be included for a full refund.

• EAP300
• 12V/1A 100V~240V Power Adapter
• RJ-45 Ethernet LAN Cable
• CD-ROM with User’s Manual
• Quick Guide

System Requirements

The following are the minimum system requirements in order to configure the device.

• Computer with an Ethernet interface or Wireless Network function.
• Windows, Mac OS, or Linux-based operating systems
• Internet Explorer or Firefox or Safari Web-Browser Software

Applications

The wireless LAN products are easy to install and highly efficient. The following list describes some of the many applications made possible through the power and flexibility of wireless LANs:

• Difficult-to-wire environments
  There are many situations where wires cannot be laid easily. Historic buildings, older buildings, open areas
  and across busy streets make the installation of LANs either impossible or very expensive.
• Temporary workgroups
  Consider situations in parks, athletic arenas, exhibition centers, disaster recovery, temporary offices and
  construction sites where one wants a temporary WLAN established and removed.
• The ability to access real-time information
  Doctors/nurses, point-of-sale employees, and warehouse workers can access real-time information while
  dealing with patients, serving customers, and processing information.
• Frequently changed environments
  Showrooms, meeting rooms, retail stores, and manufacturing sites were frequently rearranged the
  workplace.
• Small Office and Home Office (SOHO) networks
  SOHO users need a cost-effective, easy, and quick installation of a small network.
• Wireless extensions to Ethernet networks
  Network managers in dynamic environments can minimize the overhead caused by moves, extensions to
  networks, and other changes with wireless LANs.
• Wired LAN backup
  Network managers implement wireless LANs to provide backup for mission-critical applications running on
  wired networks.
• Training/Educational facilities
  Training sites at corporations and students at universities use wireless connectivity to ease access to
  information, information exchanges, and learning.

Before you Begin

This section will guide you through the installation process. Placement of the ENGENIUS EAP300 is very important to avoid poor signal reception and performance. Avoid placing the device in enclosed spaces such as a closet, cabinet, or wardrobe.

Considerations for Wireless Installation

The operating distance of all wireless devices cannot be pre-determined due to a number of unknown obstacles in the environment that the device is deployed. These could be the number, thickness, and location of walls, ceilings, or other objects that the wireless signals must pass through. Here are some key guidelines to ensure that you have the optimal wireless range.

• Keep the number of walls and ceilings between the EnGenius access point and other network devices to a minimum. Each wall or ceiling can reduce the signal strength; the degradation depends on the building’s material.
• Building materials make a difference. A solid metal door or aluminum stubs may have a significant negative effect on
  range. Locate your wireless devices carefully so the signal can pass through drywall or open doorways. Materials such as glass, steel, metal, concrete, water (fish tanks), mirrors, file cabinets, and brick will also degrade your wireless signal.
• Interferences can also come from your other electrical devices or appliances that generate RF noise. The most usual types are microwaves or cordless phones.

Computer Settings (Windows XP/Windows 7)

This device can be configured as an Access Point, WDS AP, or WDS Bridge. The default IP address of the device is 192.168.1.1 (In Access Point Mode as default). In order to log into this device, you must first configure the TCP/IP settings of your PC/Notebook.

• Click the Start button and open the Control Panel.
• Windows XP, click [Network Connection].
• Windows 7, click [View Network Status and Tasks] then [Change adapter settings].
• Right-click on [Local Area Connection] and select [Properties].
• Select “Internet Protocol (TCP/IP)” and click [Properties].
• Select “Use the following IP address” and enter the IP address and subnet mask then click [OK].

Apple Mac X OS

• Go to System Preferences > Network
• Under the Network setting, select “Manually” and enter the IP address and subnet mask.
• Click Apply when done.

Hardware Installation

1. Place the unit in an appropriate location after conducting a site survey.
2. Plug one end of the Ethernet cable into the Ethernet port of the device and another end into your PC/Notebook.
3. Insert the DC-inlet of the power adapter into the port labeled “DC-IN” and the other end into the power socket on the wall.

This diagram depicts the hardware configuration.

Configuring Your Access Point

This section will show you how to configure the device using the web-based configuration interface.

Default Settings

Please use your Ethernet port or wireless network adapter to connect the Access Point.

Default Settings

IP Address	192.168.1.1
Username / Password	admin/admin
Operation Mode	Access Point
Wireless SSID	genius
Wireless Security	None

 

Note: X represented in the wireless SSID above is the last 6 characters of your device’s MAC Address. This can be found on the device’s body label and is unique for each device.

Web Configuration

• Open a web browser (Internet Explorer/Firefox/Safari) and enter the IP Address http://192.168.1.1

Note: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address.

• The default username and password are admin. Once you have entered the correct username and password, click the Login button to open the web-based configuration page.
• You will see the following webpage if log in successfully.
• The navigation drop-down menu on the left is divided into seven main sections:
  • System: This menu includes the operation mode, status, DHCP, schedule, event log, and monitor. Through this section, you can also change the device operating mode, such as Access Point, WDS AP, or WDS Bridge.
  • Wireless: This menu includes status, basic, advanced, security, filter, client list, and VLAN.
  • Network: This menu includes status, LAN, and spanning tree.
  • Management: This menu includes the admin setup, SNMP, firmware upgrade, save/restore backup, and device reset.
  • Tools: Displays the time zone, diagnostics, and LED control.
  • Logout: To log out of the system. Need to open up a new browser window in order to log in again.

System

Operation Mode

Each of the operating modes offers different features. In order to switch the operating mode, select it from the System >> Operation Mode. There are three operation modes: Access Point, WDS AP, and WDS Bridge.

A dialog box will appear to notify you that the system will restart in order for the change to take effect. Click on the OK button to continue.

Please wait while the device counts down and restarts in the new operating mode.

Status

This page will display the status of the device.

System
Operation Mode	The device is currently in which mode.
System Time	The device’s system time. If this is incorrect, please set the time in the Tools / Time page.
System Up Time	The duration about the device has been operating without powering down or reboot.
Hardware Version and Serial Number	Hardware information for this device.
Kernel and Application Version	Firmware information for this device.

WLAN Settings
Channel	The wireless channel in use.
ESSID	The SSID (Network Name) of the wireless network. (up to 4 SSIDs are supported)
Security	Wireless encryption is enabled for this SSID.
BSSID	The MAC address of this SSID.

 

Event Log

This page displays the system log of the device. When powered down or rebooted, the log will be cleared.

Event Log
Save	Save the log to a file.
Clear	Clear the log.
Refresh	Update the log.

 

Monitor

This page shows a histogram of the Ethernet and Wireless LAN traffic. Click on [Detail] to get the detailed information.

Wireless

Status

This page shows the current status of the device’s Wireless settings.

WLAN Settings
Channel	The wireless channel in use.
ESSID	The SSID (Network Name) of the wireless network. (up to 4 SSIDs are supported)
Security	Wireless encryption is enabled for this SSID.
BSSID	The MAC address of this SSID.

 

Basic

This page shows the current status of the device’s Wireless settings.

Basic
Radio	Enable or Disable the device’s wireless signal.
Mode	Select between Access Point or Wireless Distribution System (WDS) modes.
Band	Select the types of wireless clients that the device will accept.

 

Enable SSID#	Select the number of SSID’s (Wireless Network names) you would like.   You can create up to 4 separate wireless networks.
SSID#	Enter the name of your wireless network. You can use up to 32 characters.
Auto Channel	When enabled, the device will scan the wireless signals around your area and select the channel with the least interference.
Channel	Manually select which channel the wireless signal will use.
Check Channel Time	When Auto Channel is Enabled, you can specify the period of the device will scan the wireless signals around your area.

 

Wireless Distribution System (WDS)

Using WDS to connect Access Point wirelessly, and in doing so extend a wired infrastructure to locations where cabling is not possible or inefficient to implement. Note that compatibility between different brands and models is not guaranteed. It is recommended that the WDS network be created using the same models for maximum compatibility. Also, note that all Access Points in the WDS network need to use the same Channel and Security settings. To create a WDS network, please enter the MAC addresses of the Access Points that you want to be included in the WDS. There can be a maximum of four access points.

Advanced

This page allows you to configure wireless advanced settings. It is recommended the default settings are used unless the user has experience with these functions.

Advanced (Access Point / WDS AP mode)
Fragment Threshold	Specifies the size of the packet per fragment. This function can reduce the chance of packet collision. However when this value is set too low, there will be increased overheads resulting in poor

	performance.
RTS Threshold	When the packet size is smaller than the RTS Threshold, then the packet will be sent without RTS/CTS handshake which may result in incorrect transmission.
Beacon Interval	The time interval that the device broadcasts a beacon. This beacon is used to synchronize all wireless clients on the network.
DTIM Period	A Delivery Traffic Indication Message informs all wireless clients that the access point will be sending Multi-casted data.
N Data Rate	You can limit the transfer rates between the device and wireless clients. Each Modulation Coding Scheme (MCS) refers to a specific transfer speed.
Channel Bandwidth	Set whether each channel uses 20 or 40Mhz. To achieve 11n speeds, 40Mhz channels must be used.
Preamble Type	A preamble is a message that helps access points synchronize with the client.   Long Preamble is standard based so increases compatibility. Short Preamble is non-standard, so it decreases compatibility but increases performance.
Tx Power	Set the power output of the wireless signal.

Advanced (WDS Bridge mode)
Fragment Threshold	Specifies the size of the packet per fragment. This function can reduce the chance of packet collision. However when this value is set too low, there will be increased overheads resulting in poor performance.
RTS Threshold	When the packet size is smaller than the RTS Threshold, then the packet will be sent without RTS/CTS handshake which may result in incorrect transmission.
N Data Rate	You can limit the transfer rates between the device and wireless clients. Each Modulation Coding Scheme (MCS) refers to a specific transfer speed.
Channel Bandwidth	Set whether each channel uses 20 or 40Mhz. To achieve 11n speeds, 40Mhz channels must be used.

Preamble Type	A preamble is a message that helps access points synchronize with the client. Long Preamble is standard based so increases compatibility. Short Preamble is non-standard, so it decreases compatibility but increases performance.
Tx Power	Set the power output of the wireless signal.

 

Security

This page allows you to set the wireless security settings.
Note: Only in Access Point and WDS AP mode.

Security (Access Point / WDS AP mode)
SSID Selection	Select the SSID that the security settings will apply to.
Separate	Tick the box in SSID or STA to Enable Separate feature.   Separate prevents communication and data sharing between wireless stations associated with same SSID or different SSID.
Broadcast SSID	If Disabled, then the device will not be broadcasting the SSID. Therefore it will be invisible to wireless clients.

WMM

Wi-Fi Multi-Media is a Quality of Service protocol which prioritizes traffic in the order according to voice, video, best effort, and background. Note that in certain situations, WMM needs to be enabled to achieve 11n transfer speeds.

Encryption

The encryption method to be applied. You can choose from WEP, WPA pre-shared key or WPA RADIUS. ·      Disabled – no data encryption is used. ·      WEP – data is encrypted using the WEP standard. ·      WPA-PSK – data is encrypted using the WPA-PSK standard. This is a later standard than WEP, and provides much better security than WEP. If all your Wireless stations support WPA-PSK, you should use WPA-PSK rather than WEP. ·      WPA2-PSK – This is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method of encryption. ·      WPA-RADIUS – This version of WPA requires a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA standard.   If this option is selected: ·      This Access Point must have a “client login” on the Radius Server. ·      Each user must have a “user login” on the Radius Server. ·      Each user’s wireless client must support 802.1x and provide the login data when required. ·      All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required.

 

IEEE 802.1x is an authentication protocol. Every user must use a valid account to log in to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode only authenticates users by IEEE 802.1x, but it does not encrypt the data during communication.

802.1x Authentication
RADIUS Server IP Address	The IP Address of the RADIUS Server
RADIUS Server port	The port number of the RADIUS Server.
RADIUS Server password	The RADIUS Server’s password.

WEP Encryption
Authentication Type	Please ensure that your wireless clients use the same authentication type.
Key type	ASCII: regular text (recommended) HEX: for advanced users
Key Length	Select the desired option, and ensure the wireless clients use the same setting. ·      64 Bit – data is encrypted, using the default key, before being transmitted. You must enter at least the default key. For 64 Bit Encryption, the key size is 10 chars in HEX (0~9 and A~F). ·      128 Bit – data is encrypted, using the default key, before being transmitted. You must enter at least the default key. For 128 Bit Encryption, the key size is 26 chars in HEX (0~9 and A~F).
Default Key	Select the key you wish to be the default. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. You must enter a Key Value for the Default Key.
Encryption Key #	Enter the key value or values you wish to use. Only the Key selected as Default is required. The others are optional.

WPA Pre-Shared Key Encryption
Authentication Type	Please ensure that your wireless clients use the same authentication type.
WPA type	Select the WPA encryption you would like. Please ensure that your wireless clients use the same settings.
Pre-shared Key Type	Select whether you would like to enter the Key in HEX or Passphrase format.
Pre-shared Key	Wireless clients must use the same key to associate the device. If using passphrase format, the Key must be from 8 to 63 characters in length.

WPA RADIUS Encryption
WPA type	Select the WPA encryption you would like. Please ensure that your wireless clients use the same settings.
RADIUS Server IP address	Enter the IP address of the RADIUS Server
RADIUS Server Port	Enter the port number used for connections to the RADIUS server.
RADIUS Server password	Enter the password required to connect to the RADIUS server.

 

Network

Status

This page shows the current status of the device’s LAN connection.

LAN

This page allows you to modify the device’s LAN settings.

LAN IP
Bridge Type	Select Static IP or Dynamic IP from the drop-down list. If you select Static IP, you will be required to specify an IP address and subnet mask. If Dynamic IP is selected, then the IP address is received automatically from the external DHCP server.
IP address	The LAN IP Address of this device.
IP Subnet Mask	The LAN Subnet Mask of this device.
Default Gateway	The Default Gateway of this device. Leave it blank if you are unsure of this setting.
DNS Type	Select Static or Dynamic from the drop-down list.
First / Second DNS Address	The first / second DNS address for this device.

 

DHCP Server feature is only in Access Point mode.

DHCP Server (Access Point mode)
DHCP Server	Enable or disable DHCP feature. The DHCP Server automatically allocates IP addresses to your LAN device. Disabled as default.
Lease Time	The duration of the DHCP server allocates each IP address to a LAN device.
Start / End IP	The range of IP addresses of the DHCP server will allocate to LAN device.
Domain name	The domain name for this LAN network.
First / Second DNS Address	The first / second DNS address for this LAN network.

 

Spanning Tree

This page allows you to modify the Spanning Tree settings. Enabling Spanning Tree protocol will prevent network loops in your LAN network.

Management

Admin

This page allows you to change the system password and to configure remote management. By default, the password is: admin. Password can contain 0 to 12 alphanumeric characters and are case sensitive.

Change Password
Old Password	Enter the current password.
New Password	Enter your new password.
Confirm Password	Enter your new password again for verification.
Idle Timeout	Enter Administration Page timeout time.

 

SNMP

This page allows you to assign the contact details, location, community name and trap settings for SNMP. This is a networking management protocol used to monitor network-attached devices. SNMP allows messages (called protocol data units) to be sent to various parts of a network. Upon receiving these messages, SNMP-compatible devices (called agents) return data stored in their Management Information Bases.

SNMP
SNMP Active	Enable or disable SNMP feature.
SNMP Version	You may select a specific version or select All from the drop-down list.
Read Community	Specify the password for access the SNMP community for read only access.
Set Community	Specify the password for access to the SNMP community with read/write access.
System Location	Specify the location of the device.
System Contact	Specify the contact details of the device
Trap
Trap Active	Enable or disable SNMP trapping feature.
Trap Manager IP	Specify the IP address of the computer that will receive the SNMP traps.
Trap Community	Specify the password for the SNMP trap community.

 

Firmware Upgrade

This page allows you to upgrade the device’s firmware.

To perform the Firmware Upgrade:

1. Click the [Browse] button and navigate to the location of the upgrade file.
2. Select the upgrade file. Its name will appear in the Upgrade File field.
3. Click the [Apply] button to commence the firmware upgrade.

Note: The device is unavailable during the upgrade process, and must restart when the upgrade is completed. Any connections to or through the device will be lost.

Emergency Upgrade

If you upgrade fail, you may enter Emergency Upgrade WEB page.

1. Enter IP address: 192.168.99.9 and enter Emergency Upgrade WEB page.
2. Click the [Browse] button and navigate to the location of the upgrade file and then click [Upload].
3. Wait for 60 seconds for firmware upgrade and reboot the device.
4. You can access the device again.

Configure

This page allows you to save the current device configurations. When you save the configurations, you also can re-load the saved configurations into the device through the [Restore Settings]. If extreme problems occur you can use the [Restore to Factory Defaults] to set all configurations to its original default settings.

Configure
Restore to Factory Default	Restores the device to factory default settings.
Backup Settings	Save the current configuration settings to a file.
Restore Settings	Restores a previously saved configuration file. Click Browse to select the file. Then Upload to load the settings.

 

Reset

In some circumstances it may be required to force the device to reboot. Click on [Apply] to reboot.

Tools

Time Setting

This page allows you to set the system time.

Time
Time Setup	Select the method you want to set the time.
Time Zone	Select the time zone for your current location.
NTP Time Server	Enter the address of the Network Time Protocol (NTP) Server to automatically synchronize with a server on the Internet.
Daylight Savings	Check whether daylight savings applies to your area.

 

Diagnosis

This page allows you to test your network. Type in the address for diagnosis.

Diagnosis
Address to Ping	Enter the IP address you like to see if a successful connection can be made.
Ping Frequency	Select the frequency for Ping test.
Ping Result	The results of the Ping test.

 

LED Control

This page allows you to control LED on/off for Power, LAN interface and WLAN interface.

Logout

Click on [Logout] button to logout.

Appendix A – FCC Interference Statement

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FAQs EnGenius N300 Access Point Up to 300 Mbps

For More Post Visit: Manuals Dock

[embeddoc url=”https://manualsdock.com/wp-content/uploads/2023/08/EnGenius-N300-Access-Point-Up-to-300-Mbps.pdf” download=”all”]