Welcome to ManualsDock! Read Millions of manuals for free.

Get 20% off and boost your website's speed with Hostinger Cloud Hosting!

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers User Manual

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers featured

DS18 LOGO

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers

PACKAGING INCLUDES

  • 1 Pair 10” Wakeboard Pod Tower Speaker
  • 1 Piece 6 mm Hex wrench Chromed
  • 1 Piece 4 mm Hex wrench Chromed
  • 1 Pair NBR Pad For 1” to 3“ Tube
  • 1 Pair Stainless Safety Rope
  • 1 Pcs Screw Fastening Glue

NOTE
The stainless steel hardware supplied with your speakers has been chosen to resist rust and corrosion. If the particular hardware supplied will not work for your installation purposes, please be sure to use only appropriate marine-grade (stainless steel) mounting hardware.

READ BEFORE INSTALLATION

  1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
  2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
  3. For easier assembly, we suggest you have all your tools in hand, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
  4. Use high-quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
  5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines, or electrical wiring when working on any vehicle. If installing in a boat, make sure not to cut or drill through the main hull.
  6. Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
  7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
  8. Ensure the mounting clamp or “L” bracket is tight before leaving the dock.
  9. Decide early what type of LED lighting you want (if any) and wire accordingly (NOTE: if you want “Dancing Light” look to the WiFi or RF or BT remote-controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

  • An Electric Drill With Bits
  • Allen / Hex Key / Wrench Set
  • Philips Head And Standard Screw Drivers
  • Wire Strippers
  • Crimping Tool
  • Vom (Electronic Volt Ohm Meter)
  • Heat Shrink Tubing And Heat Gun
  • Soldering Iron
  • Electronic (Rosen Not Acid Core) solder

BEGINNING MOUNTING

Step 1
Remove tower speakers from the packaging and ALL hardware.

Step 2
Find a GOOD location that allows for easy wiring of the speaker (and LED lights) -PLUS does NOT impair your movement around the location.

Step 3
Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp.

Step 4
Drill a 15 – 20 mm hole on the mounting tube bottom and align the clamp wire out the hole.

Step 5
Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.

Step 6
Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 1

Step 7
Wrap the rubber pad around the pipe and align the wire out the hole According to the diagram.

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 2

Step 8
Push the wire into the tube, press on the rubber pad, and lock the top clamp.

Step 9
Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 3

Step 10
If need be, rotate the speakers for best dispersion, this is easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base and rotating the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!

Step 11
During the mounting process, you should have located the spot to drill your tower bar for the insertion of 6 conductor wires (Speaker and RGB lightning wiring). Or NOT (see Tie-wrap solution below).

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 4

Step 12
Remove Wire NBR Plug and Slide the wire through the hole Snake the wire down to the bottom of the tower tube in a location where the wires can be attached to the audio (And lighting) system. The solder or butt connects the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water/moisture.

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 5

Step 13
When you want to install a flat mounting, remove the clamp and remove the 6 core through it into the flat mounting bracket, then assemble it, see the depiction below.

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 6

SETUP

INSTALLATION & CONNECTION OPTIONS

  1. If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
  2. DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 7To connect without LED Control Module 2 (LED-BTC), Connect as Shown in the Following Diagram:
  • Black wire”BK” connected to battery Positive (+) 12V
  • White Color Light “R”; “B” and “G” connected to battery Negative (-)
  • Green Color Light “G” connected to battery Negative (-)
  • Red Color Light “R” connected to battery Negative (-)
  • Blue Color Light “B” connected to battery Negative (-)
  • Purple Color Light “R” and “B” connected to battery Negative (-)
  • Yellow Color Light” R” and “G” connected to battery Negative (-)
  • Cyan Color Light “B” and “G” connected to battery Negative (-)

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 8

SPECIFICATIONS

  • Nominal Diameter ……………………………………………………………………………………………………………..10”
  • Nominal Impedance ………………………………………………………………………………………………………4 ohm
  • RMS Power handling …………………………………………………………………………………………………….. 300W
  • MAX Power Handling ……………………………………………………………………………………………………. 900W
  • Sensitivity (1w/1m) …………………………………………………………………………………………………….. 100dB
  • Frequency Response …………………………………………………………………………………………..45Hz-22KHz
  • Recommended HI Pass Crossover……………………………………………………………………………………55Hz

BODY / FEATURES

  • Enclosure Material…………………………………………………………………………………………….. Injection ASA
  • Marine Grade Type……………………………………………………………………………………….. IP65 + UV Stable
  • RGB LED Lighting: ………………………………………………………..Integrated RGB LED Speaker Lighting, Integrated RGB LED Acrylic Ring Lighting, and with 6 Core Wires for Lighting and Speaker
  • Grill Type……………………………………………………………………………… ASA + 316 Stainless Metal Mesh
  • Single or Pair……………………………………………………………………………………………………………………..Pair
  • Clamps …………………………………………………………………………………………Die-Cast Adjustable (1″~2″) 360 Degree Rotation Mounting, Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware (Screws, Stop Washers, Hexagon wrench,
    Safety Rope, Screw fastening Glue)
  • Front Logo …………………………………………………….. Yes, Can be Rotated for Correct Angle Display
  • Rear Logo ……………………………………………………………………………………………Radiator Fixed Position

WOOFER SPECIFICATIONS

  • Voice Coil Diameter………………………………………………………………………………………………………………2″
  • Cone Material …………………………………………………………………….Water Resistant Compress Paper
  • Surround Material……………………………………………………………………………….Soft PC Damping Glued
  • Basket Material ………………………………………………………………………PC Injection Molded Composite
  • Magnet Material………………………………………………………………………………………………….. Neodymium
  • Magnet Grade …………………………………………………………………………………………………………………N40H
  • Passive Radiator……………………………………………………………………………….. 6.1” with RGB LED Light

DRIVER SPECIFICATIONS

  • Voice Coil Diameter……………………………………………………………………………………………………………1.5″
  • Type………………………………………………………. Compression Driver With CNC Solid Aluminum Horn
  • Diaphragm Material………………………………………………………………………………………………… Polyimide
  • Magnet Material………………………………………………………………………………………………….. Neodymium
  • Crossover……………………………………………………………………………. 12dB with Overpower Protection

THIELE & SMALL PARAMETERS

  • Equivalent Volume……………………………..Vas…………………………………………………………………..33.24L
  • Excursion (one way)……………………………Xmax …………………………………………………………………6 mm
  • Free Air Resonance …………………………….Fs ………………………………………………………………………62 Hz
  • Total Factor………………………………………..Qts …………………………………………………………………. 0.7371

MEASUREMENTS

  • Overall Diameter ……………………………………………………………………………………….10.76” / 273.3 mm
  • Overall Depth…………………………………………………………………………………………….15.21” / 386.4 mm
  • Overall Height……………………………………………………………………………………………14.32” / 363.9 mm

COLORS AVAILABLE

  • Matte Black ……………………………………………………………………………………………..NXL-X10TPNEO/BK
  • Glossy White…………………………………………………………………………………………..NXL-X10TPNEO/WH
  • Glossy Red………………………………………………………………………………………………. NXL-X10TPNEO/RD

DIMENSIONS

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 9

DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers 10

WARRANTY

Please visit our website DS18.com for more information on our warranty policy.

For more Manuals by DS18, visit MANUALSDOCK

FAQS About DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers

What is the power handling of these speakers?

The DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers have a maximum power handling of 550 watts RMS per pair, 1100 watts peak power.

What is the impedance of these speakers?

These speakers have a nominal impedance of 4 ohms.

Are these speakers weatherproof?

Yes, these speakers are designed to withstand harsh marine environments and are fully weatherproof.

What is the size of the speaker cone?

The DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers feature a 10-inch speaker cone.

Do these speakers come with mounting hardware?

Yes, these speakers come with mounting brackets and hardware for easy installation on your boat or marine vessel.

Can these speakers handle high volumes without distortion?

Yes, these speakers are designed to deliver clear and crisp sound even at high volumes without distortion.

Do these speakers come with LED lights?

Yes, these speakers feature built-in RGB LED lights that can be controlled to change colors according to your preference.

Are these speakers compatible with Bluetooth devices?

No, these speakers are passive and require an external amplifier to power them. However, you can connect them to a Bluetooth-enabled amplifier for wireless streaming.

What is the frequency response of these speakers?

The frequency response of the DS18 NXL-X10TPNEO Neodymium Marine Tower Speakers is 45Hz – 23kHz.

Can these speakers be used in saltwater environments?

Yes, these speakers are specifically designed for marine use and can withstand exposure to saltwater without corrosion or damage.

Leave a Comment